Sponsored Content
Special Forums IP Networking Quick Poll: Solaris IP Multipathing Post 44390 by RTM on Friday 5th of December 2003 08:57:18 AM
Old 12-05-2003
I have never seen it set up on any servers - but then again, most of the servers were running Solaris 2.6 or did not have the hardware.

It is being implemented in other parts of the company I work for - (different areas have different ideas of what should be done). Or at least it is known and suggested.

I think it's not out there much because you don't normally get failures on interface cards. If the failure rate was higher, then it would be used more. I've seen more cables go bad than cards (due to clumsy people) and it's normally fixed at the same time it was broken. I can't remember the last time a system was down due to an interface card.
 

7 More Discussions You Might Find Interesting

1. Solaris

Quick question about Solaris =)

:D Just curious, I know that solaris 2.0-2.x_present are System V UNIX... But, I have only used Solaris 10, 9 and 2.5... On a 2.5 Sparc box, after you login you get presented with the usual SunOS 5.5.1 then UNIX(R) System V Release 4.0 I know Solaris 9 and 10 do not include this banner... ... (0 Replies)
Discussion started by: ssorel
0 Replies

2. Solaris

solaris multipathing

I have solaris 10 sparc. I installed a Qlogic hba card. This card is connected on a brocade switch and the brocade is connected on 2 different controllers on a Hitachi disk bay. I formated 2 luns. On my solaris system, i have 4 disk. How to configure solaris 10 to fix the dual disk view. ... (4 Replies)
Discussion started by: simquest
4 Replies

3. Solaris

Solaris IP Multipathing (IPMP) Help

Hello All, I work for a Health care company at a local trauma hospital. I maintain a Picture Archiving and Communication System (PAC's). Basically, any medical images (X-Ray, CT, MRI, Mammo, etc) are stored digitally on the servers for viewing and dictation from diagnostic stations. I took over... (10 Replies)
Discussion started by: mainegeek
10 Replies

4. Solaris

Solaris IP Multipathing

Hi, I saw your post on the forums about how to setup IP multipathing. I wanted your help on the below situation . I have 2 servers A and B . Now they should be connected to 2 network switches . S1 and S2. Now is it possible to have IP Multipathing on each of the servers as follows ? ... (0 Replies)
Discussion started by: maadhuu
0 Replies

5. Solaris

Disable Inbuilt multipathing software of Solaris 10

Dear UNIX Gurus I need to know how to disable MPXIO feature (Inbuilt multipathing software of Solaris 10) as we are going to implemented iSCSI EMC based SAN. I am bit new to this feature so kindly suggest how to disable it Regards (4 Replies)
Discussion started by: girish.batra
4 Replies

6. Solaris

Solaris multipathing

Hai we using emc storage which is conneted to M5000 through san switch. we asign 13 luns but in server it is showing 22 luns. i enable the solaris multipathing (MPxIO) #more /kernel/drv/fp.conf in that file MPxio-disable=no #mpathadm list lu it shows ... (2 Replies)
Discussion started by: joshmani
2 Replies

7. Solaris

ZeusIOPS multipathing failed Solaris 11

hi, just installed solaris 11.1 (11.1.9.5.1) on a sun7410 ZFSSA (x4440 + j4400), but when I enable multipathing with "stmsboot -e", only the 1TB SATA drives inside the j4400 are configured as multipathed vhci / mpxio devices, but the logzillas / ZeusIOPS drives are skipped. the server is... (0 Replies)
Discussion started by: pressy
0 Replies
vga_setchipset(3)						Svgalib User Manual						 vga_setchipset(3)

NAME
vga_setchipset - force chipset SYNOPSIS
#include <vga.h> void vga_setchipset(int chipset); DESCRIPTION
Force detection of a chipset (when chipset detection fails). vga_setchipset(VGA) can be useful if the chipset specific stuff or the SVGA detection stuff gives problems. However, at first the automatic detection should work well, and if not a specific chipset can be forced from /etc/vga/libvga.config. Because of that, void vga_setchipset(int chipset) should probably never be used by applications. If used nevertheless, it should be called directly before vga_init(3). As of now the following values are defined for chipset: UNDEFINED This is the default and specifies autodetection. VGA A plain VGA card, not that the SVGA must behave like an ordinary SVGA card then which will probably mean it is in an ordinary (25x80) textmode. ET4000 Tseng ET4000/ET4000W32(i/p) cards. CIRRUS Cirrus Logic GD542x/3x cards. TVGA8900 Trident TVGA 8900C/9000 (and possibly also 8800CS/8900A/B) cards. OAK Oak Technologies OTI-037/67/77/87 cards. EGA An ordinary EGA card. The notes about VGA apply. S3 An S3 base card. ET3000 Tseng ET3000 cards. MACH32 A card (from ATI or not) based on the ATI Mach32 chipset. GVGA6400 A Genoa(?) GVGA6400 card. ARK ARK Logic ARK1000PV/2000PV cards. ATI An ATI SVGA (VGA Wonder and friends) card. This does not (necessarily) include the newer cards (usually called Mach something). ALI An ALI2301 based card. MACH64 A card using the ATI Mach64 chipset. Support is not complete. CHIPS Chips and Technologies chipsets 65525, 65535, 65546, 65548, 65550, and 65554 (usually in laptops). SEE ALSO
svgalib(7), vgagl(7), libvga.config(5), vgatest(6), vga_getcurrentchipset(3), vga_setchipsetandfeatures(3) AUTHOR
This manual page was edited by Michael Weller <eowmob@exp-math.uni-essen.de>. The exact source of the referenced function as well as of the original documentation is unknown. It is very likely that both are at least to some extent are due to Harm Hanemaayer <H.Hanemaayer@inter.nl.net>. Occasionally this might be wrong. I hereby asked to be excused by the original author and will happily accept any additions or corrections to this first version of the svgalib manual. Svgalib (>;= 1.2.11) 27 July 1997 vga_setchipset(3)
All times are GMT -4. The time now is 07:25 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy