11-19-2003
No NIC Card?
Hello Everyone,
While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use.
There is no output for dmesg|grep eth. Does that mean that mandrake is not able to locate my network card?
While booting it says "eth0 Initialization delayed"?
Can any one solve my problem?
Thanks in advance.
10 More Discussions You Might Find Interesting
1. HP-UX
using sam i have tryed to configure the nic, however when i try to do so i get an error saying i couldn't as i was using BIND ? (0 Replies)
Discussion started by: bobstar01
0 Replies
2. Linux
Hi PPL!
I have P-IV processor, with on-board NIC card.
I have added one more NIC card for domestic use.
My kudzu does not recognise the newly added PCMCIA NIC card.
How to go about this one?
Suggest
PEnguin (0 Replies)
Discussion started by: chakri.penguin
0 Replies
3. Solaris
All,
I see that there are 2 nic card available . How can I know all the details about these 2 nic cards.
-rw-r--r-- 1 root root 10 Apr 16 15:00 hostname.bge0
-rw-r--r-- 1 root other 17 Apr 22 08:56 hostname.bge2
please let me know
thanks
-prasad (4 Replies)
Discussion started by: p4cldba
4 Replies
4. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
5. Solaris
Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than... (5 Replies)
Discussion started by: kurva
5 Replies
6. Solaris
I have configure 2 NIC in ipmp group1 .Similarly other 2 NIC in ipmp group2
When I connect both NIC to 2 different switch , which is connect to one L3 switch as trunk. Both the NIC failover to each other continously.
Following are the message log.
ifmsdb1 in.mpathd: NIC failure detected... (0 Replies)
Discussion started by: abhaymittal003
0 Replies
7. Linux
I have a linux box with 2 nic cards on it one for prod and one for backup.
My question is while the backup are happening how do I determine which nic is used for backups . I would like to run a command so that that I can see the usage in a dynamic fashion. (7 Replies)
Discussion started by: new2prog
7 Replies
8. UNIX for Advanced & Expert Users
Hi,
Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux.
I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS.... (3 Replies)
Discussion started by: devtakh
3 Replies
9. HP-UX
Hi,
Someone asked me the below.
If the box has multiple NIC cards, try to run a test with interface address specified as shown below
$ java utils.MulticastTest -N server100 -A 237.155.155.1 -i <interfaceaddress>
How can I now find out if my box has multiple NIC cards and how can I... (5 Replies)
Discussion started by: mohtashims
5 Replies
10. Red Hat
Hi,
I would like to know how to find out ACTUAL speed of NIC Card.
I have used the command ethtool eth0, it is showing supported modes,
but what is acutal speed ? how to find out? (4 Replies)
Discussion started by: manoj.solaris
4 Replies
LEARN ABOUT DEBIAN
ifscheme-mapping
IFSCHEME(8) Commands IFSCHEME(8)
NAME
ifscheme - scheme control for network interfaces
SYNOPSIS
ifscheme [-v] [[-s] newscheme]
mapping <interface> script ifscheme-mapping
DESCRIPTION
ifscheme allows you to change network configuraton schemes or query the current scheme. It integrates with the ifup(8) command and inter-
faces(5). For example, you might use this program to configure a "home" scheme and a "work" scheme for a network device on a laptop. When
you move between home and work, a simple command can reconfigure your networking.
If you run the program with no parameters, it will tell what the current network scheme is.
The ifscheme-mapping utility is used to tell the ifup and ifdown utilities about the current scheme.
OPTIONS
-v
--verbose
Run in verbose mode. This is passed in to the ifup and ifdown programs as well.
-l
--list list all schemes available/defined in /etc/network/interfaces.
newscheme
-s newscheme
--scheme newscheme
Change to a new network configuration scheme. When the scheme is changed, network interfaces that were using the old scheme will be
taken down and brought back up to use the new configuration scheme. -s or --scheme are mandatory if newscheme begins with a -.
CONFIGURATION
To make the program do anything useful when a scheme is selected, you must edit /etc/network/interfaces to add a mapping for the interface
(or interfaces) that can be controlled on a per-scheme basis. Suppose you want to control eth0 in this way. You might have an existing eth0
configuraton in there, such as:
auto eth0
iface eth0 inet static
address 192.168.1.5
netmask 255.255.255.0
gateway 192.168.1.1
To change this so you can chose between static routing and dhcp, replace it with the following (it helps to ifdown the interface first).
auto eth0
mapping eth0
script ifscheme-mapping
iface eth0-home inet static
address 192.168.1.5
netmask 255.255.255.0
gateway 192.168.1.1
iface eth0-work inet dhcp
Now if you run "ifscheme home" and ifup the interface, you'll get the eth0-home configuration stanza. If you run "ifscheme work", it will
be changed to the eth0-work stanza. You can add additional stanzas as desired, but the label must always be of the form <hardware inter-
face>-<scheme name>.
If you have a second interface (perhaps a wireless network card on eth1), you can duplicate the above for that interface, changing the eth0
and the configuration details as appropriate, but remember to add an iface stanza for every scheme name for the second interface.
FILES
/etc/network/interfaces
the interfaces definition file
/etc/network/run/scheme
the current scheme
/etc/network/run/ifstate
a record of the current state of the interfaces, managed by ifup and ifdown
BUGS
All schemed interfaces will have the same scheme.
Any schemed interface which does not have an entry for the current scheme and is not configured when the scheme is changed will not be suc-
cessfully configured when it is brought up.
SEE ALSO
interfaces(5) ifup(8) ifdown(8)
DISTRIBUTION
Redistribution is subject to the GNU public license.
AUTHORS
Joey Hess <joey@kitenet.net>, Peter Wilson <pwilson@cs.hmc.edu>
IFSCHEME(8)