11-19-2003
No NIC Card?
Hello Everyone,
While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use.
There is no output for dmesg|grep eth. Does that mean that mandrake is not able to locate my network card?
While booting it says "eth0 Initialization delayed"?
Can any one solve my problem?
Thanks in advance.
10 More Discussions You Might Find Interesting
1. HP-UX
using sam i have tryed to configure the nic, however when i try to do so i get an error saying i couldn't as i was using BIND ? (0 Replies)
Discussion started by: bobstar01
0 Replies
2. Linux
Hi PPL!
I have P-IV processor, with on-board NIC card.
I have added one more NIC card for domestic use.
My kudzu does not recognise the newly added PCMCIA NIC card.
How to go about this one?
Suggest
PEnguin (0 Replies)
Discussion started by: chakri.penguin
0 Replies
3. Solaris
All,
I see that there are 2 nic card available . How can I know all the details about these 2 nic cards.
-rw-r--r-- 1 root root 10 Apr 16 15:00 hostname.bge0
-rw-r--r-- 1 root other 17 Apr 22 08:56 hostname.bge2
please let me know
thanks
-prasad (4 Replies)
Discussion started by: p4cldba
4 Replies
4. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
5. Solaris
Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than... (5 Replies)
Discussion started by: kurva
5 Replies
6. Solaris
I have configure 2 NIC in ipmp group1 .Similarly other 2 NIC in ipmp group2
When I connect both NIC to 2 different switch , which is connect to one L3 switch as trunk. Both the NIC failover to each other continously.
Following are the message log.
ifmsdb1 in.mpathd: NIC failure detected... (0 Replies)
Discussion started by: abhaymittal003
0 Replies
7. Linux
I have a linux box with 2 nic cards on it one for prod and one for backup.
My question is while the backup are happening how do I determine which nic is used for backups . I would like to run a command so that that I can see the usage in a dynamic fashion. (7 Replies)
Discussion started by: new2prog
7 Replies
8. UNIX for Advanced & Expert Users
Hi,
Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux.
I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS.... (3 Replies)
Discussion started by: devtakh
3 Replies
9. HP-UX
Hi,
Someone asked me the below.
If the box has multiple NIC cards, try to run a test with interface address specified as shown below
$ java utils.MulticastTest -N server100 -A 237.155.155.1 -i <interfaceaddress>
How can I now find out if my box has multiple NIC cards and how can I... (5 Replies)
Discussion started by: mohtashims
5 Replies
10. Red Hat
Hi,
I would like to know how to find out ACTUAL speed of NIC Card.
I have used the command ethtool eth0, it is showing supported modes,
but what is acutal speed ? how to find out? (4 Replies)
Discussion started by: manoj.solaris
4 Replies
LEARN ABOUT DEBIAN
sinfod
SINFOD(8) User Manuals SINFOD(8)
NAME
sinfod - a monitoring tool for networked computers
SYNOPSIS
sinfod [-F] [-q] [-V] [-b #.#.#.#] [-c] [-n card ] [ -N nicevalue ] [ -m marker ] [ -i processname ] [-s][-W]
DESCRIPTION
sinfod distributes system information to other sinfods on your local network.
These Information include the system load, memory utilization and the `TOP-5' processes on every machine.
It's main advantage is, that these informations are broadcasted using the udp(7) protocol.
If each node broadcasts it's information in a cooperative manner, the network load is O(N), where N is the number of nodes in your network.
Other systems to monitor your cluster load (e.g. rup(1) ) are using a polling scheme where every node has to ask every other node for the
system information: In that case the network load is O(N**2).
The task of sinfod is to broadcast the relevant information for the local node and to collect broadcasts from other nodes. Other programs
( sinfo(1) ) can get access to this information via a simple tcp(7) connection that normally is routed through the local loopback inter-
face.
OPTIONS
-F/--foreground
Unlike normal operation, sinfod will not detach from the terminal when given this option. Some debugging informations will be visi-
ble.
-q/--quiet
Start quietly - for init scripts.
-V/--version
Print the version number and exit.
-b #.#.#.#/--bcastaddress=#.#.#.#
Set the broadcast address of the sinfod. Default is 255.255.255.255. In you want to run sinfod without a network card "-b
127.0.0.1" may be necessary.
-c/--cmdline
Broadcast the full command line of a process instead of the command only.
-m marker/--marker=marker
Mark the machine with a name. e.g. laboratory, pool or cluster.
-i/--ignore <process>
Don't broadcast any information on <process> ; --ignore may be set multiple times.
-t/--top <count>
Broadcast information on the top <count> processes; default: 5
-n card/--networkcard=card
Set the name of the network card whose informations will be broadcasted. (e.g. eth0). Default is the network card that saw the most
traffic at the start of sinfod.
-N nicevalue/--nice=nicevalue
Set the priority of this demon to nicevalue. Default is 15.
-s/--spymode
Deactivate the TCP interface and the collection of received packets. The demon starts in a broadcast-only mode.
-W/--watchdog
Start with simple watchdog.
AUTHOR
Juergen Rinas <jrinas@gmx.de>
SEE ALSO
sinfo(1),sshallsinfo(1),
Linux JANUARY 2005 SINFOD(8)