08-12-2003
.....
when you are using vmware, you have to choose which kind of interface you would like to use: bridged, nat, host-only, none.. so you have to adjust your defaultrouter (gateway) ..
ipconfig in windows is ifconfig in unix.....
to learn more about, type: man ifconfig
greetings Preßy
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi all,
Have two DEC Alpha 3000 systems (I think they're considered legacy servers) that I acquired from my former employer prior to the Voluntary Administrator seizing the assets.
They both have the basic SCO V4.0f OS installed and too be honest, I've had little time to even turn them on. ... (2 Replies)
Discussion started by: Cameron
2 Replies
2. IP Networking
I'm running FreeBSD 6.2 and suddenly lost connectivity to the net. After unplugging the router and checking all the connections I could find nothing wrong. All the driver software seems to be intact. I thought I would remove the driver software and restore it. However, when I go to root and type
... (5 Replies)
Discussion started by: Aaron Van
5 Replies
3. Red Hat
I had a strange problem.Recently, I virtualized my RHEL 5 system by installing Fedora 8 as guest operating system. The installation went fine. But, after installation my internet connection stopped working. Any suggestions?. I was on TataIndicom wireless USB modem. I haven't had any problems with... (3 Replies)
Discussion started by: jaghelp323
3 Replies
4. Solaris
Hello,
I am a relative UNIX newbie and we are unable to get out to the internet past the router. I can ping everything within the network but can't get out on a consistent basis. The UNIX DBA was let go recently and I have had to step in and assume his duties. Unfortunately, I am not quite... (1 Reply)
Discussion started by: judo42
1 Replies
5. UNIX for Dummies Questions & Answers
Hi,
Could some please help me in configuring wireles internet on redhat linux installed on my laptop.
When I booted using windows, I saw the following, which I think is the name of my laptop's wireless card:
Intel(R) PRO/Wireless 3945ABG Network Connection
Regards,
Girish. (0 Replies)
Discussion started by: girish1428
0 Replies
6. UNIX for Advanced & Expert Users
Hi,
Could some please help me in configuring wireles internet on redhat linux installed on my laptop.
When I booted using windows, I saw the following, which I think is the name of my laptop's wireless card:
Intel(R) PRO/Wireless 3945ABG Network Connection
I have run the following steps... (1 Reply)
Discussion started by: girish1428
1 Replies
7. Red Hat
Hi,
Could some please help me in configuring wireles internet on redhat linux installed on my laptop.
When I booted using windows, I saw the following, which I think is the name of my laptop's wireless card:
Intel(R) PRO/Wireless 3945ABG Network Connection
I have run the following steps... (9 Replies)
Discussion started by: girish1428
9 Replies
8. UNIX and Linux Applications
Hi Everyone!
A friend of mine is looking for a way to limit time his kids spent on the internet. I told him he should try out Squid proxy server. He now tries to find a way to limit total time spend on the internet to "X" hours a day, at any time during the day.
I remember there are built-in... (3 Replies)
Discussion started by: togr
3 Replies
9. UNIX for Dummies Questions & Answers
Hello fellow users and enthusists. I am in need of assistance.
I have installed Solaris 10 on a Gateway AMD Athlon 64 system. It is set up to dual boot with Windows 7. I am attempting to get internet access through another Windows 7 box, which is sharing its wireless internet connection with... (0 Replies)
Discussion started by: jl2215
0 Replies
10. Red Hat
Hi all, I setup redhat in VMware and I connected to internet, so I want setup sofware for redhat over internet what is command I used ? Are you understand my question, my ability of english is not good, such as I want setup dhcp packet I must used a command ? (yum... or...apt-get...or rpm... ?... (4 Replies)
Discussion started by: ilinux9
4 Replies
LEARN ABOUT OPENSOLARIS
telnetrc
telnetrc(4) File Formats telnetrc(4)
NAME
telnetrc - file for telnet default options
DESCRIPTION
The .telnetrc file contains commands that are executed when a connection is established on a per-host basis. Each line in the file con-
tains a host name, one or more spaces or tabs, and a telnet(1) command. The host name, DEFAULT, matches all hosts. Lines beginning with the
pound sign (#) are interpreted as comments and therefore ignored. telnet(1) commands are case-insensitive to the contents of the .telnetrc
file.
The .telnetrc file is retrieved from each user's HOME directory.
EXAMPLES
Example 1: A sample file.
In the following example, a .telnetrc file executes the telnet(1) command, toggle:
weirdhost toggle crmod
# Always export $PRINTER
DEFAULT environ export PRINTER
The lines in this file indicate that the toggle argument crmod, whose default value is "off" (or FALSE), should be enabled when connecting
to the system weirdhost. In addition, the value of the environment variable PRINTER should be exported to all systems. In this case, the
DEFAULT keyword is used in place of the host name.
FILES
$HOME/.telnetrc
SEE ALSO
telnet(1), in.telnetd(1M), environ(5)
SunOS 5.10 9 Jan 1998 telnetrc(4)