03-20-2003
Hi Jose,
You have to do
smit route
Static Routes
Move cursor to desired item and press Enter.
List All Routes
Add a Static Route
Remove a Static Route
Flush Routing Table < never do this!!!!!!!
at first List All Routes
2. TCP/IP Adress from the Telnet-PC
add a Static Route
!!! read the Command or man route
good luck
erwin
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
:confused:
Hi:
I donīt know how to add route gateway and when restart the machine lose this route and put other.
In SCO ver 5.6 Enterprise write:
etc\route delete gateway
route add gateway 199.199.1.1.
so , netstat -rn to see if has change -> all ok
Restart -> !!!... (2 Replies)
Discussion started by: AlvaroD
2 Replies
2. UNIX for Dummies Questions & Answers
I need some help adding routes in sco.
I am using SCO Openserver 5.0.4.
Basically I have 2 gateways here. The first is 10.15.1.1 and allows me access to the rest of the computers in the office and in other offices.
The other gateway is 10.15.10.2 and is the sonicwall that will allow access... (3 Replies)
Discussion started by: cstovall
3 Replies
3. HP-UX
I am using HP-UX 11i and I need to add another default gateway.
how can I do that ? (3 Replies)
Discussion started by: salhoub
3 Replies
4. UNIX for Dummies Questions & Answers
hi!
whenever i run /etc/rc.d/netif it will read rc.conf and add the pc IP and netmask but it wont read the default gateway resulting lost connectivity to internet
my rc.conf:
when i issue /etc/rc.d/netif restart:
the result of running netif to routing tables:
# netstat -rn
i... (3 Replies)
Discussion started by: rdns
3 Replies
5. Solaris
Hi Community,
I've a question about network adaptors.
I've installed Solaris 10 configuring the ce0 port with an IP(10.23.8.15) , an interface_name (first) and a gateway(10.23.8.1) .
I need to change the name of the interface ce0 and to configure another interface (ce1) with another... (1 Reply)
Discussion started by: Sunb3
1 Replies
6. Linux
Dear Sir
I am a newbie in the world of IP telephony. I have been working with Asterisk PBX (SIP) and Cisco Call Manager (MGCP) but now I am learning on how to work GNUGK for H.323 Gatekeeper.
I am having a problem, configuring static call routing on GNUGK
in the section
... (0 Replies)
Discussion started by: mfondoum
0 Replies
7. AIX
I just reinstalled a fresh install of 5300 07 on an old 44p model 170, after installing I set an IP Address on en2 and I tried to the ping default gateway, no response. I tried a
startsrc -g tcpip
... and then I can ping the default gateway. I broke the ping and tried again to ping. I cannot... (1 Reply)
Discussion started by: asyed123
1 Replies
8. Solaris
Hi,
OS: Solaris 11.2 64bit
IP address: 172.16.10.10
Netmask: 255.255.254.0
Gateway: 172.16.2.254
From windows box, i can set and ping gateway. IP address is same segment with windows box. But on solaris i cannot set gateway.
route add default 172.16.2.254
add net default: gateway... (6 Replies)
Discussion started by: mzainal
6 Replies
9. Linux
Hi,
This is the routing table on a RHEL 7 server :
# route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
0.0.0.0 10.132.81.145 0.0.0.0 UG 100 0 0 eno49
10.132.81.144 0.0.0.0 255.255.255.240 U 100 0 0 eno49... (4 Replies)
Discussion started by: anaigini45
4 Replies
10. UNIX for Beginners Questions & Answers
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
LEARN ABOUT CENTOS
telnet-probe
TELNET-PROBE(1) General Commands Manual TELNET-PROBE(1)
NAME
telnet-probe - lightweight telnet-like port probe
SYNOPSIS
$PCP_BINADM_DIR/telnet-probe [-c] [-v] host port
DESCRIPTION
telnet-probe allows the pmdashping(1) daemons to establish connections to arbitrary local and remote service-providing daemons so that
response time and service availability information can be obtained.
The required host and port number arguments have the same meaning as their telnet(1) equivalents.
The -c option causes telnet-probe to perform a connect(2) only. This skips the read(2) and write(2) exercise that would otherwise be done
after connecting (see below).
The -v option causes telnet-probe to be verbose while operating.
Once the telnet connection has been established, telnet-probe reads from stdin until end-of-file, and writes all the input data to the tel-
net connection. Next, telnet-probe will read from the telnet connection until end-of-file, discarding whatever data it receives. Then
telnet-probe exits.
To operate successfully, the input passed via telnet-probe to the remote service must be sufficient to cause the remote service to close
the connection when the last line of input has been processed, e.g. ending with ``quit'' when probing SMTP on port 25.
By default telnet-probe will not produce any output, unless there is an error in which case a diagnostic message can be displayed (in ver-
bose mode only) and the exit status will be non-zero indicating a failure.
PCP ENVIRONMENT
Environment variables with the prefix PCP_ are used to parameterize the file and directory names used by PCP. On each installation, the
file /etc/pcp.conf contains the local values for these variables. The $PCP_CONF variable may be used to specify an alternative configura-
tion file, as described in pcp.conf(5).
DIAGNOSTICS
If telnet-probe succeeds, then 0 will be returned. If the attempt to establish a connection fails or is terminated, then a non-zero exit
status is returned.
SEE ALSO
PCPintro(1), pmdashping(1), pmie(1), telnet(1), connect(2), read(2) and write(2).
Performance Co-Pilot PCP TELNET-PROBE(1)