cable modem to sparc Post: 30716

10 More Discussions You Might Find Interesting

1. IP Networking

unix and the cable modem

If the cable modem that the cable company is using doesn't support unix is there a way around that . Are there drivers I can get online or is there a way to configure redhat lenix (that's what I will be using) to work with the cable modem. Or is there a way to buy a third party cable modem that...

2. UNIX for Dummies Questions & Answers

Linux and my cable modem

I recently installed Caldera 2.4 (successfully:p ), but I cannot seem to get my cable modem up and running! My ISP is AT&T and I'm using @home. I've tried using DHCP and that didn't work either. I briefly read the cable modem HOWTO, but the lsmod didn't list my network card (3COM). What do I do now?

3. UNIX for Dummies Questions & Answers

can't get my cable modem up

Caldera eDesktop 2.4 - Cable Modem my NIC card has been detected, but funny scenario: #dmesg eth0: RealTek rtl8139 Fast Ethernet at 0x2400, IRQ 0, 00:50:ba:43:a0:ef /*I noticed that it detected the correct module (rtl8139) but I'm using D-Link and not RealTek, which uses the same module....

4. UNIX for Dummies Questions & Answers

Is anyone using unix with cable modem

Is anyone using a cable modem with unix and if so does your cable co. support unix or did you get that going on your own and how. Thank you for all your help.

5. IP Networking

DHCP Linux and cable modem

I can do all this in windows, but Im trying to run the SuSe 8.0 professional as a gateway. I have the local (private) LAN setup with no problems, but Im having troubles getting it to use DHCP to go out on the external card to the service provider, which only uses Dynamic IP's. WHere, what and how...

6. UNIX for Dummies Questions & Answers

Installing Cable Modem on Irix Machine.

Ok I am new to this and wondering if there is any way of connecting a cable modem to an SGI that is running IRIX 6.5 and how to do it...

7. BSD

cable modem problem

hi I want to setup my cable modem under OpenBSD. I did not configure my network while installing the system. When I type, I get # ifconfig -a lo0 : .... ... ... rl0 : .... ... ... vr0 : ... ... ... I have two network cards (the machine will be a router). I created...

8. Solaris

Is the cable you are using a null modem cable or a modem cable

Hi all, Is there any difference between a null modem cable or a modem cable ? i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup. please correct if i am wrong, thks

9. Solaris

Null modem cable in Ultra sparc 10

Hi Gurus, Can I use null modem cable in Ultra sparc 10 workstation Thanks

10. OS X (Apple)

Cannot access UNIX.com with new cable modem

Hi. I have a very strange problem, so strange I don't even know which sub-forum to post it to. Last week, my cable modem broke, so I took it back and got a new one. The new one doesn't work with my old router so, for now, I have to connect the modem directly to my Mac with an ethernet...

LEARN ABOUT REDHAT

apcsmart

APCSMART(8)						      Network UPS Tools (NUT)						       APCSMART(8)

NAME

       apcsmart - Driver for American Power Conversion Smart Protocol UPS equipment

NOTE

       This  man  page	only  documents the hardware-specific features of the apcsmart driver.	For information about the core driver, see nutups-
       drv(8).

SUPPORTED HARDWARE

       apcsmart should recognize all APC models that use a serial protocol at 2400 bps.  This is primarily the Smart-UPS and Matrix-UPS lines, but
       some Back-UPS Pro models are also supported.

       Some older hardware may only report a handful of variables.  This is usually not a bug - they just don't support anything else.

CABLING

       This  driver  expects  to  see  a  940-0024C cable or a clone by default.  You can switch to the 940-0095B dual-mode cable support with the
       cable= definition described below.

       If your 940-0024C cable is broken or missing, use this diagram to build a clone:

       http://www.exploits.org/nut/library/cables/940-0024C.jpg

EXTRA ARGUMENTS

       This driver supports the following optional settings in the ups.conf(5):

       cable=940-0095B
	      Configure the serial port for the APC 940-0095B dual-mode cable.

       sdtype=num
	      Use shutdown type num, according to this table:

	      0: soft shutdown or powerdown, depending on battery status

	      1: soft shutdown followed by powerdown

	      2: instant power off

	      3: power off with grace period

	      Modes 0 and 1 will power up the load when power returns.	Modes 2 and 3 will keep the load turned off when the power returns.

BUGS

       Some older APC UPS models return bogus data in the status register during a front panel test.  This is usually detected and discarded,  but
       some other unexpected values have occasionally slipped through.

AUTHOR

       Russell Kroll

SEE ALSO

   The core driver:
       nutupsdrv(8)

   Internet resources:
       The NUT (Network UPS Tools) home page: http://www.exploits.org/nut/

       NUT mailing list archives and information: http://lists.exploits.org/

								  Tue Oct 22 2002						       APCSMART(8)