Hi,
I am uising Suse linux on my system and i tried :
man ethtool and i got the manual for ethtool but when i tried to use the command as:
ethtool -a eth0
it says Command not found.
also, i tried rpm -qa|grep ethtool i got:
ethtool-3-15.2 so,it means my system has ethtool server or... (4 Replies)
Hi,
I'm using ethtool to change network settings:
Just for the experiment, i want to change speed to 10, instead of 100,
I type:
ethtool -s eth0 speed 10 duplex full autoneg off
and to view settings i type:
ethtool eth0, and get this:
Settings for eth0:
Supported ports:
... (4 Replies)
Hello, I've got a FreeBSD 6 server running on my network that I used as a file server for my main computer. However I've really become frustrated with the slow up/down speeds I'm getting, about 100KB/s, which is about as bad as if I was using a "real" server. My setup is as follows:
ISP
|... (4 Replies)
Hi,
We have a website running on a local centos 5.4 surfer, static IP.
The domain.com uses no-ip.com to take care of the DNS, it forwards all to my server.
My router receives the port 80 call, routes it to my server and the world can see domain.com perfectly fine.
However, we cannot see... (3 Replies)
Hi,
I have a script that, basically, has two input files of this type:
file1
key1=value1_1_1
key2=value1_2_1
key4=value1_4_1
...
file2
key2=value2_2_1
key2=value2_2_2
key3=value2_3_1
key4=value2_4_1
...
My files are 10k lines big each (approx).
The keys are strings that don't... (7 Replies)
Hi, there is an incompatibility between my NIC and my Western Digital Powerline adapters which appears to cause autonegotiation to fail intermittently, most often following a reboot. Running the following Ethtool script will establish a connection immediately:
#!/bin/sh
# chkconfig: 345 85... (12 Replies)
Hello all. I have VSFTP up and ruining on ubuntu 10.04. It works great inside LAN, however when it comes to using it outside i have some problems. If i try to connect from filezila i get the listing and if i try to download it shows it will take forever to receive a file which is larger then 1mb,... (2 Replies)
Hi All,
I am trying to find my NIC card speed in centos 5. But i am unable to get the info using ethtool command.
# ethtool eth0
Settings for eth0:
Link detected: yes
and even tried to look for the file # cd /sys/class/net/eth0/speed files which is also not available.... (8 Replies)
Discussion started by: sravani25
8 Replies
LEARN ABOUT NETBSD
ixg
IXG(4) BSD Kernel Interfaces Manual IXG(4)NAME
ixg -- Intel(R) 10Gb Ethernet driver
SYNOPSIS
ixg* at pci? dev ? function ?
DESCRIPTION
The ixg driver provides support for PCI 10Gb Ethernet adapters based on the Intel(R) 82598EB and 82599 10 GbE Controllers. The driver sup-
ports Jumbo Frames, TCP Segmentation Offload (TSO).
For questions related to hardware requirements, refer to the documentation supplied with your Intel 10GbE adapter. All hardware requirements
listed apply to use with NetBSD.
Support for Jumbo Frames is provided via the interface MTU setting. Selecting an MTU larger than 1500 bytes with the ifconfig(8) utility
configures the adapter to receive and transmit Jumbo Frames. On NetBSD, the maximum MTU size for Jumbo Frames is 9000 bytes.
This driver version supports VLANs. For information on enabling VLANs, see ifconfig(8).
HARDWARE
The ixg driver supports the following cards:
o Intel(R) 10 Gigabit XF SR/AF Dual Port Server Adapter
o Intel(R) 10 Gigabit XF SR/LR Server Adapter
o Intel(R) 82598EB 10 Gigabit AF Network Connection
o Intel(R) 82598EB 10 Gigabit AT CX4 Network Connection
DIAGNOSTICS
ixg%d: Unable to allocate bus resource: memory A fatal initialization error has occurred.
ixg%d: Unable to allocate bus resource: interrupt A fatal initialization error has occurred.
ixg%d: watchdog timeout -- resetting The device has stopped responding to the network, or there is a problem with the network connection
(cable).
SUPPORT
For general information and support, go to the Intel support website at: http://support.intel.com.
SEE ALSO arp(4), netintro(4), vlan(4), ifconfig(8)HISTORY
The ixg device driver comes from FreeBSD, where it is called ixgbe(4). It first appeared in NetBSD 6.0.
AUTHORS
The ixg driver was written by Intel Corporation <freebsdnic@mailbox.intel.com>. It was imported from FreeBSD into NetBSD by
David Young <dyoung@NetBSD.org>.
BUGS
The hardware supports a maximum MTU of 16114 bytes, but the NetBSD port of the driver supports only 9000 bytes.
The hardware supports Message-Signalled Interrupts (MSI and MSI-X) and Receive-Side Scaling (RSS), however, these features are not enabled in
the NetBSD driver at this time.
BSD July 25, 2011 BSD