Setup a site to site VPN between two cisco routers.
One of the site locations is unable to access ports such as https://example.com:9001
How do I let them go into port 9001?
They can ssh, ftp, telnet and everything else.
Is this a VPN issue or ACL access issue?
I put
permit ip host... (0 Replies)
hello guys,
I have a file like this:
input.dat
Push-to-talk
No
Coonection
IP support
Support for IP telephony
Yes
Built-in SIP stack
Yes
Support via software
Yes
Microsoft
Support for Microsoft Exchange
Yes
UMA (5 Replies)
Hi,
I am trying to establish vpn between my linux server and cisco asa at client side.
I installed openswan on my cent os.
Linux Server
eth0 - 182.2.29.10
Gateway - 182.2.29.1
eth1 - 192.9.200.75
I have simple IPtables Like
WAN="eth0"
LAN="eth1" (0 Replies)
Q: "Does Cisco 1921 router support,, act as an endpoint for, site to site VPNs using IPSec? If so, how many? "
A: If you get the Cisco 1921/k9 with the security services bundle then it will have built in security features. Cisco, typically includes IP Sec tunnels I believe as part of that... (0 Replies)
Hi @all,
I try to connect 2 LANs with IPSec/Openswan
LAN 1: 192.168.0.0/24
LAN 2: 192.168.1.0/24
This is my Config:
conn HomeVPN # # Left security gateway, subnet behind it, nexthop toward right. left=192.168.1.29 ... (1 Reply)
I'm trying to figure out what circumstances would cause an Open Solaris 11.2 host to switch itself from a static to a DHCP ip address upon reboot. This has only happened once but is a cause for some concern as this machine will be part of a web server pool.
Nothing has changed on the LAN that... (2 Replies)
Having given up for the time being with a very difficult game engine project to virtualizing cyberspace, am working on the forums again.
Just updated a few icons on the mobile site. Explanations in the picture captions:
https://www.unix.com/members/1-albums214-picture855.jpeg
... (1 Reply)
Hey,
I have enable post thanks (viewing thanks, not yet giving thanks) in mobile:
https://www.unix.com/members/1-albums214-picture1018.jpeg
I plan to also add the button to "give thanks on mobile.
In addition, I will change the formatting (color and justification) of this new mobile... (1 Reply)
Discussion started by: Neo
1 Replies
LEARN ABOUT NETBSD
genfb
GENFB(4) BSD Kernel Interfaces Manual GENFB(4)NAME
genfb -- generic framebuffer console driver
SYNOPSIS
genfb* at pci?
genfb* at sbus?
wsdisplay* at genfb?
DESCRIPTION
The genfb driver provides support for generic framebuffers that have no native driver. All it needs are some parameters to describe the
framebuffer and an address.
PCI
When attaching to a pci(4) bus the driver is configured via device properties:
width (uint32)
Width in pixels.
height (uint32)
Height in pixels.
stride (uint32)
Line size in bytes.
depth (uint32)
Bits per pixel.
is_console (bool)
If true, genfb will try to become the system console.
address (uint32)
Bus address of the framebuffer.
SBus
When attaching to sbus(4) all those parameters are retrieved from the firmware.
SEE ALSO pci(4), sbus(4), wscons(4), wsdisplay(4)BUGS
There is no way to change the color map even when the firmware supports it. The pci(4) bus frontend has only been tested on macppc, i386,
and amd64 and requires machine dependent code to pass the properties mentioned above. So far only macppc, i386, and amd64 provides them.
BSD August 23, 2009 BSD