port access to site to site VPN


Login or Register for Dates, Times and to Reply

 
Thread Tools Search this Thread
# 1  
port access to site to site VPN

Setup a site to site VPN between two cisco routers.

One of the site locations is unable to access ports such as https://example.com:9001

How do I let them go into port 9001?

They can ssh, ftp, telnet and everything else.

Is this a VPN issue or ACL access issue?

I put
permit ip host 10.0.0.0 host 192.0.0.0

tried adding this
permit tcp host 10.0.0.3 host 192.0.0.5
but nothing

so they should be able to access???Smilie
Login or Register for Dates, Times and to Reply

Previous Thread | Next Thread
Thread Tools Search this Thread
Search this Thread:
Advanced Search

Test Your Knowledge in Computers #155
Difficulty: Easy
Defense Advanced Research Projects Agency (DARPA) initiated the ARPANET, the precursor to the Internet, in 1969.
True or False?

9 More Discussions You Might Find Interesting

1. Post Here to Contact Site Administrators and Moderators

Regarding not able to access UNIX.com site

Hello MODs/Admins, Could you please help me here as from last 6 to 7 days I(and checked with my fellow friends too) am not able to access unix.com site at all. It is very very slow, it never loads completely. Even I checked with different people and different computers it results same only,... (8 Replies)
Discussion started by: RavinderSingh13
8 Replies

2. IP Networking

IPSec Openswan Site to Site VPN - Big Pain

Hi @all, I try to connect 2 LANs with IPSec/Openswan LAN 1: 192.168.0.0/24 LAN 2: 192.168.1.0/24 This is my Config: conn HomeVPN # # Left security gateway, subnet behind it, nexthop toward right. left=192.168.1.29 ... (1 Reply)
Discussion started by: bahnhasser83
1 Replies

3. IP Networking

Does cisco 1921 router support site to site VPNs using IPSec?

Q: "Does Cisco 1921 router support,, act as an endpoint for, site to site VPNs using IPSec? If so, how many? " A: If you get the Cisco 1921/k9 with the security services bundle then it will have built in security features. Cisco, typically includes IP Sec tunnels I believe as part of that... (0 Replies)
Discussion started by: Ayaerlee
0 Replies

4. IP Networking

iptables allow access to one site

Hi all I need help with a set of iptables rules that would allow a portion of a bank of ipaddresses acces to only one or two named wbsites. Please advise Thank You Ed (3 Replies)
Discussion started by: wa1ed
3 Replies

5. IP Networking

VPN ssh access over RDP port?

Guys, Can I use an open RDP port to gain ssh access to my Linux server running the other side of our firewall? I work from home on the odd occasion, we only have RDP port 3389 available once logged into the VPN. I would rather ssh into my workstation without the need for a desktop display. ... (3 Replies)
Discussion started by: general_lee
3 Replies

6. Red Hat

Want to unblock port for particular site

Dear All We have one Centos Server on Asterisk platform.We are trying to open one particular site from client machines which is our client portal.We have to upload data on that.When we trying to open that site somewhere its blocking and not opening.We did tracert and found one router down... (3 Replies)
Discussion started by: Vaibhav.T
3 Replies

7. IP Networking

How to establish site to site vpn - Linux machine and cisco asa?

Hi, I am trying to establish vpn between my linux server and cisco asa at client side. I installed openswan on my cent os. Linux Server eth0 - 182.2.29.10 Gateway - 182.2.29.1 eth1 - 192.9.200.75 I have simple IPtables Like WAN="eth0" LAN="eth1" (0 Replies)
Discussion started by: ashokvpp
0 Replies

8. UNIX for Advanced & Expert Users

squid: Allow access to only one site and only via 80 or 443

Can someone please give me the conf file line to allow access to myexample.com and only that site, and only through http and https? So far I have only that site accessible via http, but all https sites are opened. Squid 3.1 on Cent 6 ---------- Post updated at 12:06 PM ---------- Previous... (0 Replies)
Discussion started by: glev2005
0 Replies

9. Shell Programming and Scripting

How to check site access in shell script

Hello every one, I have a little issue that has been killing me now for the past couple of days, I have tried to find solutions online, but its been hard to, ok here it goes... I have created a site that is based on amount of user that have access at a time, based on cookie. So if the browser... (1 Reply)
Discussion started by: heman007
1 Replies
XmDropSiteRegister(library call)										  XmDropSiteRegister(library call)

NAME
XmDropSiteRegister -- A Drag and Drop function that identifies a drop site and assigns resources that specify its behavior SYNOPSIS
#include <Xm/DragDrop.h> void XmDropSiteRegister( Widget widget, ArgList arglist, Cardinal argcount); DESCRIPTION
XmDropSiteRegister identifies the specified widget or gadget as a drop site and sets resource values that define the drop site's behavior. The routine assigns default values to any resources that are not specified in the argument list. The toolkit generates a warning message if a drop site is registered with XmNdropSiteActivity set to XmDROP_SITE_ACTIVE and the XmNdropProc resource is NULL. If the drop site is a descendant of a widget that is registered as a drop site, the XmNdropSiteType resource of the ancestor drop site must be specified as XmDROP_SITE_COMPOSITE. The ancestor must be registered before the descendant. The drop site is stacked above all other sib- ling drop sites already registered. widget Specifies the ID of the widget to be registered. arglist Specifies the argument list. argcount Specifies the number of attribute/value pairs in the argument list (arglist). For a complete definition of DropSite and its associated resources, see XmDropSite(3). RELATED
XmDisplay(3), XmDropSite(3), XmDropSiteEndUpdate(3), XmDropSiteStartUpdate(3), XmDropSiteUpdate(3), XmDropSiteUnregister(3), and XmScreen(3). XmDropSiteRegister(library call)

Featured Tech Videos