06-13-2019
trevian,
You'll need to be able to get a console that you are able to use to get the wwn's from the adapters. The problem that I see, and posted about above, is that your PCI bus appears to have a fault. So it is very likely AIX won't be able to see your adapters to get the zoning information. IBM or someone with intimate knowledge of AIX/Power error codes could really decode the full errpt to know what else needs to be replaced on this frame.
10 More Discussions You Might Find Interesting
1. IP Networking
Im newest in unix,
Please, give me solution for installing lan adapter if driver not found in the list of ethernet drivers
ihave unix driver in a dos diskete
please give me the other solution
and tell me where the domain of unix class online, so ican read from it.
Thank's very much (3 Replies)
Discussion started by: ade_muhdiat
3 Replies
2. Solaris
Hi. I need to find a simple SCSI adapter card for a Sun Ultra 5 workstation. I don't need the type w/ ethernet attached (e.g. X1032) as I already have ethernet onboard & they are more spendy.
I know Adaptec is out, but what unit would work? I am attaching an external SCSI tape unit to this... (4 Replies)
Discussion started by: Plain Person
4 Replies
3. Solaris
Hi everyone, it's me the Solaris novice once again. Here's my situation.
- I bought a Sun Ultra 10 Creator 3D Workstation and Sony 19" SVGA Monitor package deal.
- The system has the Creator 3D Video Adapter installed but I could not use it because the adapter has a 13w3 connection and my... (5 Replies)
Discussion started by: jbarbuto
5 Replies
4. HP-UX
Hi ,
Hi what is an adapter?what is its use ?
How to log into a tibco server from unix home directory. (1 Reply)
Discussion started by: megh
1 Replies
5. UNIX for Dummies Questions & Answers
Hi all, I got sort of a task to do. I have to write in C "simulated network driver". What does it mean?
- It has to run on all network adapters
- It has to be as simple as it can be
- It has to run on all linux distributions (or at least most of them)
- It does not have to run a network... (4 Replies)
Discussion started by: Chrisdot
4 Replies
6. SCO
I inserted a PCI Realtek RTL8139 network adapter on a PC running SCO Openserver 5.0.6.
I successfully loaded drivers and I'm trying to install the card with netconfig command, unfortunately without success.
Here are the steps I follow to install the card:
I run netconfig, from menu 'hardware'... (2 Replies)
Discussion started by: kampus
2 Replies
7. Hardware
I need to connect 80pin SCA Ultra320 SCSI hdd to 68pin.
There are rumors that some bad "passive" adapters with problematic termination can fry the HDD. The adapter we got is Assmann ABSCA-2. Hard drive is 'Fujitsu MAW3073NC'
Do we need to set any jumpers before turning it on?
We already had... (0 Replies)
Discussion started by: orange47
0 Replies
8. AIX
Hello,
Runing VIO and couple lpars on POWER blade.
I want to dedicate graphics adapter(ati0) to one lpar. Is that possible ?
I tried to do that using IVM (I/O Adapter Management->View/Modify Physical Adapters->Modify partition assignment):
Failed to remove adapter U78A6.001.WIH4088-P2-C8... (1 Reply)
Discussion started by: vilius
1 Replies
9. AIX
Hi,
I want to change from vscsi to npiv. Is it possible to use both on the same adapter, so we can change the systems one by one, or must we place a second FC adapter in the VIO servers?
Thanks,
Ronald (2 Replies)
Discussion started by: ronaldm60
2 Replies
10. Red Hat
Hi,
I have installed Oracle Enterprise Linux 5 in my PC. After the installation the Ethernet Card is not got detected.
But I could able to get the details using the command lspci -a:
01:00.0 Ethernet controller: Attansic Technology Corp. L1 Gigabit Ethernet Adapter (rev b0).
But I could... (4 Replies)
Discussion started by: chidhu.anu
4 Replies
TR(4) BSD Kernel Interfaces Manual TR(4)
NAME
tr -- TROPIC based shared memory Token-Ring cards device driver
SYNOPSIS
tr0 at isa? port 0xa20 iomem 0xd800 irq ?
tr* at isa? port ? irq ?
tr* at isapnp?
tr* at mca? slot ?
tr* at pcmcia? function ?
DESCRIPTION
The tr device driver supports TROPIC I based shared-memory Token-Ring cards.
HARDWARE
Supported cards include the following IBM and 3Com models:
IBM Token-Ring Network PC Adapter
IBM Token-Ring Network PC Adapter II
IBM Token-Ring Network Adapter/A
IBM Token-Ring Network 16/4 Adapter
IBM Token-Ring Network 16/4 Adapter/A
IBM Token-Ring 16/4 Credit Card Adapter
IBM Token Ring Auto 16/4 Credit Card Adapter
IBM Turbo 16/4 Token Ring PC Card
IBM 16/4 ISA Adapter
IBM Auto 16/4 Token-Ring ISA Adapter
IBM Token Ring 16/4 Credit Card Adapter
IBM Token Ring Auto 16/4 Credit Card Adapter
IBM Turbo 16/4 Token Ring PC Card
3Com 3C619 TokenLink
3Com 3C319 TokenLink Velocity
3Com 3C389 TokenLink Velocity PC Card
SOURCE ROUTING
Setting IFF_LINK0 enables Token-Ring source routing. Setting IFF_LINK1 uses all-routes broadcasts otherwise single-route broadcasts are
used.
NOTES
The MCA attachment has been only tested on IBM Token Ring 16/4 Adapter/A so far. It doesn't support ifmedia(4) yet, too.
SEE ALSO
ifmedia(4), intro(4), isa(4), isapnp(4), mca(4), pcmcia(4), ifconfig(8)
HISTORY
The tr driver appeared in NetBSD 1.4.
BUGS
The PCMCIA attachment does not work with the cbb(4) CardBus driver.
BSD
April 14, 1999 BSD