Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Misconfiguration detected Adapter interface name en 3 Adapter offset 0
Operating Systems AIX Misconfiguration detected Adapter interface name en 3 Adapter offset 0 Post 303035981 by RecoveryOne on Tuesday 11th of June 2019 11:16:31 AM
Old 06-11-2019
Quote:
Originally Posted by bakunin

To add to his problems: he has a HACMP cluster running and this will not recover itself from a "script error" like the one it has already run into. You need to use HACMP-recovery-procedures to get out of this state and this needs a sound understanding of how HACMP (=SystemMirror, =PowerHA) works. It is difficult to troubleshoot something as complex as a cluster over the internet and in fact it is bordering on criminal to have someone who is obviously way out of his league to administrate a system deemed valuable and mission-critical enough to warrant a (rather costly) HA-solution. This is like buying a Formula-One racing car and setting a 5-year-old behind the steering wheel.

bakunin

Yeah, the good news is depending on the other node the cluster should be up but unstable. And one can rebuild/reload and bring in a node to the cluster. Not a fun task by any means. That said, yes troubleshooting hacmp via forums would be a nightmare. I was hoping at the very least to help them get the system up enough to see what was going on.



@trevian3969:
Depending on the criticality of this system, and to parrot what bakunin said it very likely will be worth while to look at upgrading to something newer. If you have a good IBM rep, see if they can get you a discount on some AIX classes with purchase of new frames. The redbooks for HACMP, and AIX are also a wealth of knowledge. When I joined the sysadm team to work with AIX I knew next to nothing about it, other than it was COOL!. Still haven't been to an official class, but man pages, redbooks sites like this place here and other blogs of AIX have been indispensable to me. Sadly, I feel my coming into AIX may have been 10 years too late for all the hot sysadm stuff! Smilie


Feel free to post what questions you may have however. And I'll still try to help out as much as I can where I can, just keep in mind that in the end it's your environment. I don't know how your environment is setup. The OS is way out of date, and all that other fun stuff right? I figure if nothing else, bakunin smack me for being wrong! Hey, I still have a lot to learn!



Take care and good luck!
 

10 More Discussions You Might Find Interesting

1. IP Networking

LAN Adapter

Im newest in unix, Please, give me solution for installing lan adapter if driver not found in the list of ethernet drivers ihave unix driver in a dos diskete please give me the other solution and tell me where the domain of unix class online, so ican read from it. Thank's very much (3 Replies)
Discussion started by: ade_muhdiat
3 Replies

2. Solaris

Which SCSI Adapter?

Hi. I need to find a simple SCSI adapter card for a Sun Ultra 5 workstation. I don't need the type w/ ethernet attached (e.g. X1032) as I already have ethernet onboard & they are more spendy. I know Adaptec is out, but what unit would work? I am attaching an external SCSI tape unit to this... (4 Replies)
Discussion started by: Plain Person
4 Replies

3. Solaris

Creator 3D Video Adapter

Hi everyone, it's me the Solaris novice once again. Here's my situation. - I bought a Sun Ultra 10 Creator 3D Workstation and Sony 19" SVGA Monitor package deal. - The system has the Creator 3D Video Adapter installed but I could not use it because the adapter has a 13w3 connection and my... (5 Replies)
Discussion started by: jbarbuto
5 Replies

4. HP-UX

what is an adapter?

Hi , Hi what is an adapter?what is its use ? How to log into a tibco server from unix home directory. (1 Reply)
Discussion started by: megh
1 Replies

5. UNIX for Dummies Questions & Answers

Simulated driver for Network Interface Adapter

Hi all, I got sort of a task to do. I have to write in C "simulated network driver". What does it mean? - It has to run on all network adapters - It has to be as simple as it can be - It has to run on all linux distributions (or at least most of them) - It does not have to run a network... (4 Replies)
Discussion started by: Chrisdot
4 Replies

6. SCO

Installing LAN adapter

I inserted a PCI Realtek RTL8139 network adapter on a PC running SCO Openserver 5.0.6. I successfully loaded drivers and I'm trying to install the card with netconfig command, unfortunately without success. Here are the steps I follow to install the card: I run netconfig, from menu 'hardware'... (2 Replies)
Discussion started by: kampus
2 Replies

7. Hardware

SCSI Ultra320 80->68 adapter

I need to connect 80pin SCA Ultra320 SCSI hdd to 68pin. There are rumors that some bad "passive" adapters with problematic termination can fry the HDD. The adapter we got is Assmann ABSCA-2. Hard drive is 'Fujitsu MAW3073NC' Do we need to set any jumpers before turning it on? We already had... (0 Replies)
Discussion started by: orange47
0 Replies

8. AIX

Dedicate graphics adapter ?

Hello, Runing VIO and couple lpars on POWER blade. I want to dedicate graphics adapter(ati0) to one lpar. Is that possible ? I tried to do that using IVM (I/O Adapter Management->View/Modify Physical Adapters->Modify partition assignment): Failed to remove adapter U78A6.001.WIH4088-P2-C8... (1 Reply)
Discussion started by: vilius
1 Replies

9. AIX

Vscsi and npiv on same adapter

Hi, I want to change from vscsi to npiv. Is it possible to use both on the same adapter, so we can change the systems one by one, or must we place a second FC adapter in the VIO servers? Thanks, Ronald (2 Replies)
Discussion started by: ronaldm60
2 Replies

10. Red Hat

Ethernet Adapter not detected.

Hi, I have installed Oracle Enterprise Linux 5 in my PC. After the installation the Ethernet Card is not got detected. But I could able to get the details using the command lspci -a: 01:00.0 Ethernet controller: Attansic Technology Corp. L1 Gigabit Ethernet Adapter (rev b0). But I could... (4 Replies)
Discussion started by: chidhu.anu
4 Replies

LEARN ABOUT NETBSD

tr

TR(4)							   BSD Kernel Interfaces Manual 						     TR(4)

NAME

     tr -- TROPIC based shared memory Token-Ring cards device driver

SYNOPSIS

     tr0 at isa? port 0xa20 iomem 0xd800 irq ?
     tr* at isa? port ? irq ?
     tr* at isapnp?
     tr* at mca? slot ?
     tr* at pcmcia? function ?

DESCRIPTION

     The tr device driver supports TROPIC I based shared-memory Token-Ring cards.

HARDWARE

     Supported cards include the following IBM and 3Com models:

	   IBM	 Token-Ring Network PC Adapter

	   IBM	 Token-Ring Network PC Adapter II

	   IBM	 Token-Ring Network Adapter/A

	   IBM	 Token-Ring Network 16/4 Adapter

	   IBM	 Token-Ring Network 16/4 Adapter/A

	   IBM	 Token-Ring 16/4 Credit Card Adapter

	   IBM	 Token Ring Auto 16/4 Credit Card Adapter

	   IBM	 Turbo 16/4 Token Ring PC Card

	   IBM	 16/4 ISA Adapter

	   IBM	 Auto 16/4 Token-Ring ISA Adapter

	   IBM	 Token Ring 16/4 Credit Card Adapter

	   IBM	 Token Ring Auto 16/4 Credit Card Adapter

	   IBM	 Turbo 16/4 Token Ring PC Card

	   3Com  3C619 TokenLink

	   3Com  3C319 TokenLink Velocity

	   3Com  3C389 TokenLink Velocity PC Card

SOURCE ROUTING

     Setting IFF_LINK0 enables Token-Ring source routing.  Setting IFF_LINK1 uses all-routes broadcasts otherwise single-route broadcasts are
     used.

NOTES

     The MCA attachment has been only tested on IBM Token Ring 16/4 Adapter/A so far.  It doesn't support ifmedia(4) yet, too.

SEE ALSO

     ifmedia(4), intro(4), isa(4), isapnp(4), mca(4), pcmcia(4), ifconfig(8)

HISTORY

     The tr driver appeared in NetBSD 1.4.

BUGS

     The PCMCIA attachment does not work with the cbb(4) CardBus driver.

BSD
								  April 14, 1999							       BSD
All times are GMT -4. The time now is 10:11 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy