I need to delete a TTY in my AIX 4.3 system. I have tried using the smit but everytime I try it, there is a message telling me that the device is in use and cannot be changed. How do I take the device "offline", so to speak, so that I can edit the settings and/or delete it.
V/R
Djassi (3 Replies)
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Hi, I have the following packages installed on my AIX server
xlC.aix50.rte 10.1.0.2 COMMITTED XL C/C++ Runtime for AIX 5.3
xlC.cpp 9.0.0.0 COMMITTED C for AIX Preprocessor
xlC.msg.en_US.cpp 9.0.0.0 COMMITTED C for AIX Preprocessor
xlC.msg.en_US.rte 10.1.0.2 COMMITTED XL C/C++ Runtime
xlC.rte... (4 Replies)
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
NIC port is down on IBM Frame. From the back its slot C7/C8. The network switch is the problem, and a new switch will be coming into play. There's one VIO and one LPAR.
How do i tell the port is down in the OS on the VIO? And how can i verify it's backup without pulling cables? We have a... (1 Reply)
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
I have Xubuntu 18.04 installed on my PC. I have created a 10G .img image file created by QEMU-IMG. I have installed inside of it Solaris 9 SPARC edition . If I try and mount the image file as a loop device (using sudo losetup /dev/loop0 /path-to-img-file) I can only mount it as read only.
... (1 Reply)
Discussion started by: alphatron150
1 Replies
LEARN ABOUT DEBIAN
an
AN(4) BSD Kernel Interfaces Manual AN(4)NAME
an -- Aironet Communications 4500/4800 wireless network adapter driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device an
device wlan
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_an_load="YES"
DESCRIPTION
The an driver provides support for Aironet Communications 4500 and 4800 wireless network adapters and variants, including the following:
o Aironet Communications 4500 and 4800 series
o Cisco Aironet 340 and 350 series
o Xircom Wireless Ethernet Adapter
Support for these devices include the ISA, PCI and PCMCIA varieties. The Aironet 4500 series adapters operate at 1 and 2Mbps while the
Aironet 4800 series and Cisco adapters can operate at 1, 2, 5.5 and 11Mbps. The ISA, PCI and PCMCIA devices are all based on the same core
PCMCIA modules and all have the same programming interface, however unlike the Lucent WaveLAN/IEEE cards, the ISA and PCI cards appear to the
host as normal ISA and PCI devices and do not require any PCCARD support.
The PCMCIA Aironet cards require PC Card support, including the kernel pccard(4) driver. ISA cards can either be configured to use ISA Plug
and Play or to use a particular I/O address and IRQ by properly setting the DIP switches on the board. (The default switch setting is for
Plug and Play.) The an driver has Plug and Play support and will work in either configuration, however when using a hard-wired I/O address
and IRQ, the driver configuration and the NIC's switch settings must agree. PCI cards require no switch settings of any kind and will be
automatically probed and attached.
All host/device interaction with the Aironet cards is via programmed I/O. The Aironet devices support 802.11 and 802.3 frames, power manage-
ment, BSS (infrastructure) and IBSS (ad-hoc) operation modes. The an driver encapsulates all IP and ARP traffic as 802.11 frames, however it
can receive either 802.11 or 802.3 frames. Transmit speed is selectable between 1Mbps, 2Mbps, 5.5Mbps, 11Mbps or "auto" (the NIC automati-
cally chooses the best speed).
By default, the an driver configures the Aironet card for infrastructure operation.
For more information on configuring this device, see ifconfig(8).
DIAGNOSTICS
an%d: init failed The Aironet card failed to become ready after an initialization command was issued.
an%d: failed to allocate %d bytes on NIC The driver was unable to allocate memory for transmit frames in the NIC's on-board RAM.
an%d: device timeout The Aironet card failed to generate an interrupt to acknowledge a transmit command.
SEE ALSO altq(4), arp(4), miibus(4), netintro(4), wlan(4), ancontrol(8), ifconfig(8)HISTORY
The an device driver first appeared in FreeBSD 4.0.
AUTHORS
The an driver was written by Bill Paul <wpaul@ee.columbia.edu>.
BSD July 16, 2005 BSD