Sponsored Content
Operating Systems AIX AIX - NIC device explanation need Post 303035232 by Phat on Friday 17th of May 2019 12:50:41 AM
Old 05-17-2019
Hello,

Quote:
smitty tcpip --> Further configuration -->Network interface -->Network interface selection -->Configure alias
I have gone through this, but I don't see the alias IP. I think we have to put the alias IP here to remove. It's not already there for us to choose to remove Smilie


Code:
Type or select values in entry fields.
Press Enter AFTER making all desired changes.

                                                        [Entry Fields]
  Network INTERFACE                                   en6

* IPV4 ADDRESS (dotted decimal)                      []
  Network MASK (hexadecimal or dotted decimal)       []

1 more question, in the linux we can edit the ifcfg-ethx to make some changes. So on AIX, which file can we do the same to make changes to IP configuration?
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Dleting a Device in AIX 4.3

I need to delete a TTY in my AIX 4.3 system. I have tried using the smit but everytime I try it, there is a message telling me that the device is in use and cannot be changed. How do I take the device "offline", so to speak, so that I can edit the settings and/or delete it. V/R Djassi (3 Replies)
Discussion started by: djassi
3 Replies

2. UNIX for Dummies Questions & Answers

NIC and Device NO to Change

I am a beginer in unix . I would like to know what is the command in orser to change NIC and Device NO (1 Reply)
Discussion started by: Ilias Kappatos
1 Replies

3. AIX

AIX -How to find which NIC is on which PCI card

Hi All, How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v Any idea? Thanks. (2 Replies)
Discussion started by: samnyc
2 Replies

4. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies

5. AIX

Explanation of C Compiler for AIX

Hi, I have the following packages installed on my AIX server xlC.aix50.rte 10.1.0.2 COMMITTED XL C/C++ Runtime for AIX 5.3 xlC.cpp 9.0.0.0 COMMITTED C for AIX Preprocessor xlC.msg.en_US.cpp 9.0.0.0 COMMITTED C for AIX Preprocessor xlC.msg.en_US.rte 10.1.0.2 COMMITTED XL C/C++ Runtime xlC.rte... (4 Replies)
Discussion started by: jimthompson
4 Replies

6. Red Hat

I want to tune NIC's rps, rfs and xps value. which NIC device should I modify.

Dear All I want tune my NIC's rps, rfs and xps value. In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1). Here is the question? Which device should I modify ? eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0) Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies

7. AIX

AIX Frame: NIC port down

NIC port is down on IBM Frame. From the back its slot C7/C8. The network switch is the problem, and a new switch will be coming into play. There's one VIO and one LPAR. How do i tell the port is down in the OS on the VIO? And how can i verify it's backup without pulling cables? We have a... (1 Reply)
Discussion started by: gps1976
1 Replies

8. Linux

Add two different subnet public IPs to single NIC or two different NIC on same box

Hello Admins, My ask is how can I add two different subnet IPs to same box with two different gateways? The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware. How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies

9. UNIX for Beginners Questions & Answers

Configuring NIC device in Solaris 9 SPARC OS [QEMU]

I have Xubuntu 18.04 installed on my PC. I have created a 10G .img image file created by QEMU-IMG. I have installed inside of it Solaris 9 SPARC edition . If I try and mount the image file as a loop device (using sudo losetup /dev/loop0 /path-to-img-file) I can only mount it as read only. ... (1 Reply)
Discussion started by: alphatron150
1 Replies
answer(1)						      General Commands Manual							 answer(1)

NAME
answer - phone message transcription system SYNOPSIS
DESCRIPTION
The interactive program helps you to transcribe telephone (and other) messages into electronic mail. The program uses your personal alias database and the system alias database, allowing you to use aliases to address the messages. Options supports the following options: Prompt for phone-slip-type message fields. Allow addresses that are not aliases. Operation begins with the prompt. Enter a one-word alias or a two-word user name ("Words" are separated by spaces.) The user name is converted to an alias in the form where f is the first character of the first word, lastword is the second word, and all letters are shifted to lower- case. For example, is converted to the alias Without the option, the specified or converted alias must exist in the alias databases. With the option, if the processed "alias" is not in the alias databases, it is used for the address as is. The fully expanded address is displayed. With the option, you are asked for typical message slip data: Enter the appropriate data. You can put just an or nothing after the pertinent dash prompts, or you can type longer comments. Whatever you enter becomes part of the message. Lines with no added text are omitted from the message. Finally, you are prompted for a message. Enter a message, if any, ending with a blank line. The message is sent and the prompt is repeated. To end the program, enter any one of or at the prompt. EXAMPLES
User input is in normal type. With No Options This example shows a valid alias, an invalid user name, and a valid user name. In the invalid case, the converted alias is displayed in square brackets. With the -u Option If you enter the previous error is treated differently. With the -p Option If you enter the phone-slip prompts are added. The three lines with no added text are deleted from the message. FILES
User alias database data table User alias database directory table User alias database hash table User alias source text System alias database data table System alias database directory table System alias database hash table System alias source text Outbound mail message edit buffer AUTHOR
was developed by HP. SEE ALSO
elm(1), newalias(1). answer(1)
All times are GMT -4. The time now is 06:32 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy