smitty tcpip --> Further configuration -->Network interface -->Network interface selection -->Configure alias
I have gone through this, but I don't see the alias IP. I think we have to put the alias IP here to remove. It's not already there for us to choose to remove
Code:
Type or select values in entry fields.
Press Enter AFTER making all desired changes.
[Entry Fields]
Network INTERFACE en6
* IPV4 ADDRESS (dotted decimal) []
Network MASK (hexadecimal or dotted decimal) []
1 more question, in the linux we can edit the ifcfg-ethx to make some changes. So on AIX, which file can we do the same to make changes to IP configuration?
I need to delete a TTY in my AIX 4.3 system. I have tried using the smit but everytime I try it, there is a message telling me that the device is in use and cannot be changed. How do I take the device "offline", so to speak, so that I can edit the settings and/or delete it.
V/R
Djassi (3 Replies)
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Hi, I have the following packages installed on my AIX server
xlC.aix50.rte 10.1.0.2 COMMITTED XL C/C++ Runtime for AIX 5.3
xlC.cpp 9.0.0.0 COMMITTED C for AIX Preprocessor
xlC.msg.en_US.cpp 9.0.0.0 COMMITTED C for AIX Preprocessor
xlC.msg.en_US.rte 10.1.0.2 COMMITTED XL C/C++ Runtime
xlC.rte... (4 Replies)
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
NIC port is down on IBM Frame. From the back its slot C7/C8. The network switch is the problem, and a new switch will be coming into play. There's one VIO and one LPAR.
How do i tell the port is down in the OS on the VIO? And how can i verify it's backup without pulling cables? We have a... (1 Reply)
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
I have Xubuntu 18.04 installed on my PC. I have created a 10G .img image file created by QEMU-IMG. I have installed inside of it Solaris 9 SPARC edition . If I try and mount the image file as a loop device (using sudo losetup /dev/loop0 /path-to-img-file) I can only mount it as read only.
... (1 Reply)
Discussion started by: alphatron150
1 Replies
LEARN ABOUT SUSE
ifcfg-vlan
IFCFG-VLAN(5) Network configuration IFCFG-VLAN(5)NAME
ifcfg-vlan - virtual LAN interface configuration
SYNOPSIS
/etc/sysconfig/network/ifcfg-vlan*
Virtual LANs (802.1q)
To setup a vlan interface you need a configuration file that contains at least the mandatory
ETHERDEVICE
variable with the real interface used for the virtual LAN.
Further, it may contain the optional
VLAN_ID
variable that specifies the VLAN ID.
By default and when the VLAN_ID variable is not set, the number at the end of the interface name is the VLAN ID.
Preferably the interface name and the configuration file follow the VLAN interface name scheme (type), that is either:
ifcfg-vlan<VLAN-ID> (e.g. ifcfg-vlan42)
or
ifcfg-name.<VLAN-ID> (e.g. ifcfg-eth0.42)
The VLAN-ID can be also 0-padded (e.g. ifcfg-vlan0042 or ifcfg-eth0.0042).
Also in case of custom names, trailing digits are interpreted as VLAN-ID by default (e.g. ifcfg-dmz42). When VLAN_ID is set in the config,
the interface name have any name (e.g. ifcfg-foobar).
Note: The drawback of custom interface names and VLAN_ID usage is, that a rename of the interface is required and that they violate the
name scheme.
The real interface will be set UP automatically and doesn't need a config file in case of a physical interface. But without a config file
YaST will consider this interface as unused, if will not follow hotplug events and you're unable to apply any settings, e.g. ETH-
TOOL_OPTIONS. To avoid that, provide an config file with at least STARTMODE='auto'.
The rest of the VLAN interface IP and routes configuration do not differ from ordinary interfaces. See also man ifcfg and man routes for
details.
EXAMPLES
Sets up vlan3 vlan interface on top of eth0:
ifcfg-vlan3
STARTMODE='auto'
ETHERDEVICE='eth0'
IPADDR='192.168.3.27/24'
Sets up eth0.3 vlan interface on top of eth0:
ifcfg-eth0.3
STARTMODE='auto'
ETHERDEVICE='eth0'
IPADDR='192.168.3.27/24'
Sets up lan1 vlan interface with ID 42 on top of eth0:
ifcfg-lan1
STARTMODE='auto'
ETHERDEVICE='eth0'
VLAN_ID='42'
IPADDR='192.168.3.27/24'
BUGS
Please report bugs at <http://www.suse.de/feedback>
AUTHOR
Christian Zoz <zoz@suse.de>
Michal Svec <msvec@suse.cz>
Bjoern Jacke
Mads Martin Joergensen <mmj@suse.de>
Michal Ludvig <mludvig@suse.cz>
Marius Tomaschewski <mt@suse.de>
SEE ALSO routes(5), ifcfg(5), ifup(8).
sysconfig August 2004 IFCFG-VLAN(5)
05-17-2019
