Likely you are seeing an IP alias, that's why you have two ip's on the same adapter.
Now, as to two adapters with same IP, one could be disconnected at the physical layer.
**EDIT again. You can assign an IP to the ETherChannel adapter, and then the parent adapter. But its not a good way to go about it. That actually looks like what is happening here. Or someone tried to remove a backup adapter from the EtherChannel and gave it the IP.
How can I see where the alias IP is configured?
Quote:
To be honest, I'm not even sure where to begin with cleaning this up, or how far you want to go.
I can go very far
Could you shed some light on the parent Ether and child Ether?
And also with this, et is not used for IP address?
Quote:
et is used for IEE 802.3
--- Post updated at 05:18 AM ---
Hello,
After cleaning up, it's birghter
But I not yet find out where the alias IP (either 10.176.x.65 or 10.176.x.127) is configured.
I need to delete a TTY in my AIX 4.3 system. I have tried using the smit but everytime I try it, there is a message telling me that the device is in use and cannot be changed. How do I take the device "offline", so to speak, so that I can edit the settings and/or delete it.
V/R
Djassi (3 Replies)
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Hi, I have the following packages installed on my AIX server
xlC.aix50.rte 10.1.0.2 COMMITTED XL C/C++ Runtime for AIX 5.3
xlC.cpp 9.0.0.0 COMMITTED C for AIX Preprocessor
xlC.msg.en_US.cpp 9.0.0.0 COMMITTED C for AIX Preprocessor
xlC.msg.en_US.rte 10.1.0.2 COMMITTED XL C/C++ Runtime
xlC.rte... (4 Replies)
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
NIC port is down on IBM Frame. From the back its slot C7/C8. The network switch is the problem, and a new switch will be coming into play. There's one VIO and one LPAR.
How do i tell the port is down in the OS on the VIO? And how can i verify it's backup without pulling cables? We have a... (1 Reply)
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
I have Xubuntu 18.04 installed on my PC. I have created a 10G .img image file created by QEMU-IMG. I have installed inside of it Solaris 9 SPARC edition . If I try and mount the image file as a loop device (using sudo losetup /dev/loop0 /path-to-img-file) I can only mount it as read only.
... (1 Reply)
Discussion started by: alphatron150
1 Replies
LEARN ABOUT FREEBSD
if_ixgbe
IXGBE(4) BSD Kernel Interfaces Manual IXGBE(4)NAME
ixgbe -- Intel(R) 10Gb Ethernet driver for the FreeBSD operating system
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device ixgbe
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_ixgbe_load="YES"
DESCRIPTION
The ixgbe driver provides support for PCI 10Gb Ethernet adapters based on the Intel 82598EB Intel(R) Network Connections. The driver sup-
ports Jumbo Frames, MSIX, TSO, and RSS.
For questions related to hardware requirements, refer to the documentation supplied with your Intel 10GbE adapter. All hardware requirements
listed apply to use with FreeBSD.
Support for Jumbo Frames is provided via the interface MTU setting. Selecting an MTU larger than 1500 bytes with the ifconfig(8) utility
configures the adapter to receive and transmit Jumbo Frames. The maximum MTU size for Jumbo Frames is 16114.
This driver version supports VLANs. For information on enabling VLANs, see ifconfig(8).
HARDWARE
The ixgbe driver supports the following cards:
o Intel(R) 10 Gigabit XF SR/AF Dual Port Server Adapter
o Intel(R) 10 Gigabit XF SR/LR Server Adapter
o Intel(R) 82598EB 10 Gigabit AF Network Connection
o Intel(R) 82598EB 10 Gigabit AT CX4 Network Connection
DIAGNOSTICS
ixgbe%d: Unable to allocate bus resource: memory A fatal initialization error has occurred.
ixgbe%d: Unable to allocate bus resource: interrupt A fatal initialization error has occurred.
ixgbe%d: watchdog timeout -- resetting The device has stopped responding to the network, or there is a problem with the network connection
(cable).
SUPPORT
For general information and support, go to the Intel support website at: http://support.intel.com.
If an issue is identified with the released source code on the supported kernel with a supported adapter, email the specific information
related to the issue to <freebsd@intel.com>.
SEE ALSO altq(4), arp(4), netintro(4), ng_ether(4), polling(4), vlan(4), ifconfig(8)HISTORY
The ixgbe device driver first appeared in FreeBSD 7.0.
AUTHORS
The ixgbe driver was written by Intel Corporation <freebsd@intel.com>.
BSD December 19, 2010 BSD