Likely you are seeing an IP alias, that's why you have two ip's on the same adapter.
Now, as to two adapters with same IP, one could be disconnected at the physical layer.
**EDIT again. You can assign an IP to the ETherChannel adapter, and then the parent adapter. But its not a good way to go about it. That actually looks like what is happening here. Or someone tried to remove a backup adapter from the EtherChannel and gave it the IP.
How can I see where the alias IP is configured?
Quote:
To be honest, I'm not even sure where to begin with cleaning this up, or how far you want to go.
I can go very far
Could you shed some light on the parent Ether and child Ether?
And also with this, et is not used for IP address?
Quote:
et is used for IEE 802.3
--- Post updated at 05:18 AM ---
Hello,
After cleaning up, it's birghter
But I not yet find out where the alias IP (either 10.176.x.65 or 10.176.x.127) is configured.
I need to delete a TTY in my AIX 4.3 system. I have tried using the smit but everytime I try it, there is a message telling me that the device is in use and cannot be changed. How do I take the device "offline", so to speak, so that I can edit the settings and/or delete it.
V/R
Djassi (3 Replies)
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Hi, I have the following packages installed on my AIX server
xlC.aix50.rte 10.1.0.2 COMMITTED XL C/C++ Runtime for AIX 5.3
xlC.cpp 9.0.0.0 COMMITTED C for AIX Preprocessor
xlC.msg.en_US.cpp 9.0.0.0 COMMITTED C for AIX Preprocessor
xlC.msg.en_US.rte 10.1.0.2 COMMITTED XL C/C++ Runtime
xlC.rte... (4 Replies)
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
NIC port is down on IBM Frame. From the back its slot C7/C8. The network switch is the problem, and a new switch will be coming into play. There's one VIO and one LPAR.
How do i tell the port is down in the OS on the VIO? And how can i verify it's backup without pulling cables? We have a... (1 Reply)
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
I have Xubuntu 18.04 installed on my PC. I have created a 10G .img image file created by QEMU-IMG. I have installed inside of it Solaris 9 SPARC edition . If I try and mount the image file as a loop device (using sudo losetup /dev/loop0 /path-to-img-file) I can only mount it as read only.
... (1 Reply)
Discussion started by: alphatron150
1 Replies
LEARN ABOUT ULTRIX
xna
xna(4) Kernel Interfaces Manual xna(4)Name
xna - DEBNI and DEMNA Ethernet interfaces
Syntax
device xna0 at vaxbi? node? vector xnaintr (DEBNI)
device xna0 at xmi? node? vector xnaintr (DEMNA)
Description
The driver provides access to a 10 Mbytes Ethernet network through the DEBNI and DEMNA adapters. The DEBNI is an Ethernet to BI bus. The
DEMNA is an Ethernet to XMI adapter.
The host's Internet address is specified at boot time with an SIOCSIFADDR ioctl. The driver employs the Address Resolution Protocol, as
described in to map dynamically between Internet and Ethernet addresses on the local network.
The driver normally tries to use a trailer encapsulation to minimize copying data on input and output. This can be disabled for an inter-
face by setting the IFF_NOTRAILERS flag with an SIOCSIFFLAGS ioctl. Trailers are used only for packets destined for Internet hosts.
The SIOCSPHYSADDR ioctl can be used to change the physical address of the adapter and SIOCRPHYSADDR can be used to read its physical
address. SIOCADDMULTI and SIOCDELMULTI can be used to add or delete multicast addresses. The driver supports a maximum of 12 multicast
addresses. The argument to the latter ioctls is a pointer to an ``ifreq'' structure found in
SIOCRDCTRS and SIOCRDZCTRS ioctls can be used to read or read and clear network counters. The argument to the latter two ioctls is a
pointer to a counter structure ``ctrreq'' found in
The ioctls SIOCENABLBACK and SIOCDISABLBACK can be used to enable and disable the interface loopback mode.
Restrictions
The PUP protocol family is not supported.
Diagnostics
xna%d: port self-test failed:<register list>
Adapter did not pass the power-up self-test during autoconfiguration time. The port attachment fails.
xna%d: couldn't allocate...
The driver was unable to allocate memory for adapter data structures. The port attachment fails.
xna%d: port probe failed:<register list>
The driver was unable to bring the adapter into the initialized state. The port attachment fails.
xna%d: port init failed:<register list>
The driver failed to prepare the adapter for runtime use.
xna%d: port state changed, resetting:<register list>
The adapter issued a port state change interrupt. The port state is reset.
xna%d: port reset failed
The driver was unable to bring the adapter into the initialized state during a port reset.
xna%d: command failed, error code:<error code>
The adapter port command failed. The error code gives reason for failure.
xna%d: couldn't handle af%d
A packet with an undefined protocol type has been sent to the adapter.
xna%d: addmulti failed, multicast list full
Too many multicast requests have been made.
See Alsoarp(4p), inet(4f), intro(4n)xna(4)