Since the box and apps installed by vendor, the apps will not have any update and OS for 15 year and we need to pay the apps software support around 30k euro per year although no issue for last 5 year.
We plan to cancel the support but we afraid the apps corrupted or someone accidentally delete the apps file.
We did have support for hardware with oracle.
I just need the easiest way to bring up the machine if anything happen to the apps.
Did my suggestion method for disk cloning will work?
Hi ,
My Sun Machine Rebooted by itself 2 days back . Its running fine now , But i wanted to find out wat caused it to reboot...
This is wat the var/adm/messages show .
Kern.notice:- System booting after fatal error FATAL...
Wat causes this message ...
And wat tasks should i do to ensure it... (6 Replies)
Hello,
I want to change the IP of my SUN solaris machine but i am not bale to find the right way. I tried the following steps:
1) edit /etc/inet/hosts and change IP address for host listed in
/etc/hostname.le0
2) ifconfig le0 down
3) ifconfig le0 inet NEW_IP_ADDR netmask + broadcast + ... (5 Replies)
Hi I am trying to bring up our Sun V100 machine remotely using hyper terminal. We have connected LOM port A to COM1 of our windows server and have lom promt available.
Now when we type poweron it starts booting and goes through the booting process and stops at the following step...
....
... (7 Replies)
My one Sun machine is not able to ssh another machine of Sun. Although I have configured the ssh successfully
( SunOS sunbox2 5.9 Generic_118558-34 sun4u sparc SUNW,Sun-Blade-2500 )
ERROR
bash-2.05# ssh sunbox2
/etc/ssh/ssh_config: line 34: Bad configuration option: PermitRootLogin... (0 Replies)
Hi all.
Last year, after registering on Sun support site, I downloaded for free all available documentation (in PDF) and support files of a couple of old Sun workstations (Ultra 5 and Ultra 10).
Now I need the documentation and support files of other old Sun workstations (SPARCstation 20 and... (4 Replies)
-> start /SYS
Are you sure you want to start /SYS (y/n)? y
Starting /SYS
]-> show HOST
/HOST
Targets:
bootmode
diag
domain
Properties:
autorestart = reset
autorunonerror = false
bootfailrecovery = poweroff
... (29 Replies)
Discussion started by: z_haseeb
29 Replies
LEARN ABOUT NETBSD
genfb
GENFB(4) BSD Kernel Interfaces Manual GENFB(4)NAME
genfb -- generic framebuffer console driver
SYNOPSIS
genfb* at pci?
genfb* at sbus?
wsdisplay* at genfb?
DESCRIPTION
The genfb driver provides support for generic framebuffers that have no native driver. All it needs are some parameters to describe the
framebuffer and an address.
PCI
When attaching to a pci(4) bus the driver is configured via device properties:
width (uint32)
Width in pixels.
height (uint32)
Height in pixels.
stride (uint32)
Line size in bytes.
depth (uint32)
Bits per pixel.
is_console (bool)
If true, genfb will try to become the system console.
address (uint32)
Bus address of the framebuffer.
SBus
When attaching to sbus(4) all those parameters are retrieved from the firmware.
SEE ALSO pci(4), sbus(4), wscons(4), wsdisplay(4)BUGS
There is no way to change the color map even when the firmware supports it. The pci(4) bus frontend has only been tested on macppc, i386,
and amd64 and requires machine dependent code to pass the properties mentioned above. So far only macppc, i386, and amd64 provides them.
BSD August 23, 2009 BSD