03-12-2019
The good news is that you can replace the IDE disk with a SATA disk or SSD. The bad news; neither is likely to fit in the T30 case.
It has occurred to me that your notebook is not the original hardware for the following reasons:
SCO 5.0.5 was superseded by 5.0.6 prior to 1999, and 5.0.5 does not reliably run on pentium 4 systems.
https://www.unix.com/303018403-post5.html
You can switch to a SATA drive, as long as the motherboard bios supports the drive in legacy mode (emulating an iDE controller.)
This User Gave Thanks to jgt For This Post:
8 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
HI ALL,
I need to backup HDD with SCO UNIX. I need to have a full functionaly backup of this hard disk. Does anybody have any tool or subsription how to do it. I tried some SW, but after when I tried to use this copy of my original disk "can not find a root directory". Thanks in advance. (1 Reply)
Discussion started by: jardas
1 Replies
2. SCO
Hi guys,
I have this quick question , is it posible to isntall SCO 5.0.7 on a serial ATA and if it is can you tell me how or maybe a website that has some info about this.
I'm not using any raid, just one HDD.
Thanks a lot (0 Replies)
Discussion started by: josramon
0 Replies
3. UNIX for Advanced & Expert Users
Hello,
I have a P4, 2.4GHz, 256MB ASROCK mainboard: I am trying to install sco 5.0.5 on an 80gb hdd IDE .
I have tried the following techniques:
1. using the updated wd btld image- no success
2. defbootstr biosgeom
3. use interactive divvy, make adjustments using dkinit/dparam during... (0 Replies)
Discussion started by: pude
0 Replies
4. SCO
Hi guys,
I have this problem ,
One of our client's hdd went down and we cannot boot up the machine , I've installed a new hdd with a fresh copy of SCO 5.0.6 same as the one in the old HDD, i think the data still good in the old HDD.
My question!!!
How can i access the data from the fresh... (4 Replies)
Discussion started by: josramon
4 Replies
5. Ubuntu
Hi guys, I am total newbie to Linux / Ubuntu but trying it to solve the problem I have.
I have an OKI printer with bad HDD and trying to clone one from the same HDD from working printer. Board it goes on has a Fiery chipset and system used is Linux based / related - to the best of my knowlege. I... (12 Replies)
Discussion started by: Unlimitedbt
12 Replies
6. HP-UX
Hi there,
I got a pretty old HP 382 workstation, and the hdd is pretty LOUD ... ;)
So I thought I clone it to an much quiter one.
I tried this:
- removed the loud hdd
- connected it to an system running knoppix 7.0.4 (hdd is recognized with UFS filesystem; Clonezilla couldn't handle the... (9 Replies)
Discussion started by: pelegrine
9 Replies
7. SCO
Hi all
I have read about mounting crashed HDD from a sco system in this forum. However this I received an image on raw format of the crashed system that was using an IDE HDD. Which method should I mount my image? IDE scsi or USB? The image is stores in an external connected through USB .
Also... (4 Replies)
Discussion started by: OrangeKenny
4 Replies
8. AIX
Hi Folks,
I am facing an issue with the performance.
P4 with 1 processor and 16 GB RAM and SAN HDD = Oracle report takes 25 minutes
P5 with 2 processors and 16 GB RAM internall HDD with LPAR = Oracle Report takes 1 hour 15 minutes ( please note I have assigned all the max processors and... (7 Replies)
Discussion started by: filosophizer
7 Replies
LEARN ABOUT NETBSD
viaide
VIAIDE(4) BSD Kernel Interfaces Manual VIAIDE(4)
NAME
viaide -- AMD, NVIDIA and VIA IDE disk controllers driver
SYNOPSIS
viaide* at pci? dev ? function ? flags 0x0000
options PCIIDE_AMD756_ENABLEDMA
DESCRIPTION
The viaide driver supports the following IDE controllers and provides the interface with the hardware for the ata driver:
- Advanced Micro Devices AMD-756, 766, 768 and CS5536 IDE Controllers
- NVIDIA nForce, nForce2, nForce2 400, nForce3, nForce3 250, nForce4, MCP04, MCP55, MCP61, MCP65, MCP67 IDE and SATA Controllers.
- VIA Technologies VT82C586, VT82C586A, VT82C596A, VT82C686A, VT8233A, VT8235, VT8237/VT8237R IDE Controllers, VT6421 Serial RAID
Controller and CX700 IDE Controller.
The 0x0002 flag forces the viaide driver to disable DMA on chipsets for which DMA would normally be enabled. This can be used as a debugging
aid, or to work around problems where the IDE controller is wired up to the system incorrectly.
SEE ALSO
ata(4), atapi(4), intro(4), pci(4), pciide(4), wd(4), wdc(4)
NOTES
Drives on the VT6421 Serial RAID Controller can only be accessed after they have been configured into RAID or JBOD sets via its BIOS. It is
also inaptly named as it has both SATA and PATA interfaces.
BUGS
The AMD756 chip revision D2 has a bug affecting DMA (but not Ultra-DMA) modes. The workaround documented by AMD is to not use DMA on any
drive which does not support Ultra-DMA modes. This does not appear to be necessary on all drives, the PCIIDE_AMD756_ENABLEDMA option can be
used to force multiword DMA on the buggy revisions. Multiword DMA can eventually be disabled on a per-drive basis with config flags, see
wd(4). The bug, if triggered, will cause a total system hang.
The timings used for the PIO and DMA modes for controllers listed above are for a PCI bus running at 30 or 33 MHz. This driver may not work
properly on overclocked systems.
BSD
August 31, 2007 BSD