03-12-2019
The good news is that you can replace the IDE disk with a SATA disk or SSD. The bad news; neither is likely to fit in the T30 case.
It has occurred to me that your notebook is not the original hardware for the following reasons:
SCO 5.0.5 was superseded by 5.0.6 prior to 1999, and 5.0.5 does not reliably run on pentium 4 systems.
https://www.unix.com/303018403-post5.html
You can switch to a SATA drive, as long as the motherboard bios supports the drive in legacy mode (emulating an iDE controller.)
This User Gave Thanks to jgt For This Post:
8 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
HI ALL,
I need to backup HDD with SCO UNIX. I need to have a full functionaly backup of this hard disk. Does anybody have any tool or subsription how to do it. I tried some SW, but after when I tried to use this copy of my original disk "can not find a root directory". Thanks in advance. (1 Reply)
Discussion started by: jardas
1 Replies
2. SCO
Hi guys,
I have this quick question , is it posible to isntall SCO 5.0.7 on a serial ATA and if it is can you tell me how or maybe a website that has some info about this.
I'm not using any raid, just one HDD.
Thanks a lot (0 Replies)
Discussion started by: josramon
0 Replies
3. UNIX for Advanced & Expert Users
Hello,
I have a P4, 2.4GHz, 256MB ASROCK mainboard: I am trying to install sco 5.0.5 on an 80gb hdd IDE .
I have tried the following techniques:
1. using the updated wd btld image- no success
2. defbootstr biosgeom
3. use interactive divvy, make adjustments using dkinit/dparam during... (0 Replies)
Discussion started by: pude
0 Replies
4. SCO
Hi guys,
I have this problem ,
One of our client's hdd went down and we cannot boot up the machine , I've installed a new hdd with a fresh copy of SCO 5.0.6 same as the one in the old HDD, i think the data still good in the old HDD.
My question!!!
How can i access the data from the fresh... (4 Replies)
Discussion started by: josramon
4 Replies
5. Ubuntu
Hi guys, I am total newbie to Linux / Ubuntu but trying it to solve the problem I have.
I have an OKI printer with bad HDD and trying to clone one from the same HDD from working printer. Board it goes on has a Fiery chipset and system used is Linux based / related - to the best of my knowlege. I... (12 Replies)
Discussion started by: Unlimitedbt
12 Replies
6. HP-UX
Hi there,
I got a pretty old HP 382 workstation, and the hdd is pretty LOUD ... ;)
So I thought I clone it to an much quiter one.
I tried this:
- removed the loud hdd
- connected it to an system running knoppix 7.0.4 (hdd is recognized with UFS filesystem; Clonezilla couldn't handle the... (9 Replies)
Discussion started by: pelegrine
9 Replies
7. SCO
Hi all
I have read about mounting crashed HDD from a sco system in this forum. However this I received an image on raw format of the crashed system that was using an IDE HDD. Which method should I mount my image? IDE scsi or USB? The image is stores in an external connected through USB .
Also... (4 Replies)
Discussion started by: OrangeKenny
4 Replies
8. AIX
Hi Folks,
I am facing an issue with the performance.
P4 with 1 processor and 16 GB RAM and SAN HDD = Oracle report takes 25 minutes
P5 with 2 processors and 16 GB RAM internall HDD with LPAR = Oracle Report takes 1 hour 15 minutes ( please note I have assigned all the max processors and... (7 Replies)
Discussion started by: filosophizer
7 Replies
LEARN ABOUT NETBSD
cmdide
CMDIDE(4) BSD Kernel Interfaces Manual CMDIDE(4)
NAME
cmdide -- CMD Technology and Silicon Image IDE disk controllers driver
SYNOPSIS
cmdide* at pci? dev ? function ? flags 0x0000
options PCIIDE_CMD064x_DISABLE
options PCIIDE_CMD0646U_ENABLEUDMA
DESCRIPTION
The cmdide driver supports the CMD Technology PCI0640, PCI0643, PCI0646, PCI0648, PCI0649, and Silicon Image 0680 IDE controllers, and pro-
vides the interface with the hardware for the ata(4) driver.
The 0x0002 flag forces the cmdide driver to disable DMA on chipsets for which DMA would normally be enabled. This can be used as a debugging
aid, or to work around problems where the IDE controller is wired up to the system incorrectly.
SEE ALSO
ata(4), atapi(4), intro(4), pci(4), pciide(4), wd(4), wdc(4)
BUGS
There's no way to reliably know if a PCI064x controller is enabled or not. If the driver finds a PCI064x, it will assume it is enabled
unless the PCIIDE_CMD064x_DISABLE option is specified in the kernel config file. This will be a problem only if the controller has been dis-
abled in the BIOS and another controller has been installed and uses the ISA legacy I/O ports and interrupts.
The PCI0646U controller is known to be buggy with Ultra-DMA transfers, so Ultra-DMA is disabled by default for this controller. To enable
Ultra-DMA, use the PCIIDE_CMD0646U_ENABLEUDMA option. Ultra-DMA can eventually be disabled on a per-drive basis with config flags, see
wd(4).
The timings used for the PIO and DMA modes for controllers listed above are for a PCI bus running at 30 or 33 MHz. This driver may not work
properly on overclocked systems.
BSD
December 13, 2003 BSD