10-10-2018
I have no experience with boot from SAN on metal, to put a small disclaimer upfront.
Not related to the problem...what would really help you is to have a separated installed operating system on both environments (DCs), with data part replicated in separate volume groups.
That way, only thing you do is import the volume group and (possibly or not depends) an ip assignment, depending on the topology and services such as vrrp or higher layer used.
I never endorsed SAN boot on metal personally (but in vms of course), always had couple of local disks to mirror ...
Point being, i would go with service separation and clean install on each of the sites, while cloning data part via storage methods.
Hopefully someone else who used linux SAN boot will be of more assistance with the actual problem.
Regards
Peasant.
This User Gave Thanks to Peasant For This Post:
10 More Discussions You Might Find Interesting
1. Solaris
I have solaris 10 sparc. I installed a Qlogic hba card.
This card is connected on a brocade switch and the brocade is connected on 2 different controllers on a Hitachi disk bay.
I formated 2 luns. On my solaris system, i have 4 disk.
How to configure solaris 10 to fix the dual disk view.
... (4 Replies)
Discussion started by: simquest
4 Replies
2. Solaris
Hi,
I saw your post on the forums about how to setup IP multipathing. I wanted your help on the below situation .
I have 2 servers A and B . Now they should be connected to 2 network switches . S1 and S2.
Now is it possible to have IP Multipathing on each of the servers as follows ?
... (0 Replies)
Discussion started by: maadhuu
0 Replies
3. Solaris
Hai
we using emc storage which is conneted to M5000 through san switch.
we asign 13 luns but in server it is showing 22 luns.
i enable the solaris multipathing (MPxIO)
#more /kernel/drv/fp.conf in that file
MPxio-disable=no
#mpathadm list lu
it shows ... (2 Replies)
Discussion started by: joshmani
2 Replies
4. Solaris
Hello,
I turned on the server multipathing:
# uname -a
SunOS caiman 5.10 Generic_141444-09 sun4v sparc SUNW,T5140
stmsboot -D fp -e
And after a reboot the server, multipathing is not enable:
# stmsboot -L
stmsboot: MPxIO is not enabled
stmsboot: MPxIO disabled
# ls /dev/dsk... (4 Replies)
Discussion started by: bieszczaders
4 Replies
5. UNIX for Dummies Questions & Answers
Hello,
I'm trying to put puppy linux 4.2.1 (I can't use the latest because it won't boot on my hardware) on a grub2'd usb drive.
It throws the error that it can't find pup_421.sfs
Here is my /boot/grub/grub.cfg
menuentry "Puppy 4.2.1" {
loopback loop... (2 Replies)
Discussion started by: Narnie
2 Replies
6. Debian
Hello, firstly excuse for my poor english.
I have a busybox error when I try to run Debian 6. It's like Grub cannot find root (initramfs)
My system is:
- RAID0 with dmraid
- /boot ext2 (from moonOS installation --ubuntu based--)
- ext4 (moonOS wich have the Grub2 installation, where I... (0 Replies)
Discussion started by: neutralTTY
0 Replies
7. Linux
I got a dual boot with grub2, but everytime I turn on the computer and the booter is loaded, I can't handle the menu, so I am forced to wait the countdown and choose the default option.
I'd really like to know why!
This is my grub.cfg,
# # DO NOT EDIT THIS FILE # # It is automatically... (0 Replies)
Discussion started by: Luke Bonham
0 Replies
8. Red Hat
Hello
This is happening on: 3.13.7-200.fc20.x86_64
This happened already some weeks ago, until now i didn install linunx onto this machine, as i had to turn in the laptop to the service center so they could fix the UEFI flash storage.
Either way, its happening again. as i installed Fedora 20... (1 Reply)
Discussion started by: sea
1 Replies
9. Red Hat
I have a couple of questions regarding multipath.
If I do vgdisplay vg01, I see it is using 1 PV: /dev/dm-13
If I type multipath -ll I see dm-9, dm-10, dm-11, dm-12, but do not see dm-13. Is my vg01 multipathed? How can I actually know for sure?
Secondly, let's say this time vg01 says... (1 Reply)
Discussion started by: keelba
1 Replies
10. UNIX for Beginners Questions & Answers
I have centos 7 gui installed on vmware workstation12 on my laptop.WhenI want to pause my splash screen while starting my centos 7 using the 'esc key' nothing happens and the system just boots up.I also see a entry for aci_memory_fail... entry during the boot process.help me fix the system. (1 Reply)
Discussion started by: sabsac
1 Replies
lvmpvg(4) Kernel Interfaces Manual lvmpvg(4)
NAME
lvmpvg - LVM physical volume group information file
SYNOPSIS
DESCRIPTION
is an ASCII file that stores the volume-group information for all of the physical volume groups in the system. The information is stored
in a hierarchical format.
First, it starts with a volume group under which multiple physical volume groups can exist. Under each physical volume group, a list of
physical volumes can be specified. There must be at least one physical volume group in each volume group that appears in this file. The
physical-volume-group name must be unique within the corresponding volume group, although it is permissible to use a common physical volume
group name across different volume groups. There can be as many volume groups in this file as there are in the system.
Instead of using the and commands, the administrator can edit this file to create and extend physical volume groups. However, care must be
taken to ensure that all physical volumes to be included in the file have already been defined in their respective volume groups by previ-
ous use of or
The file format has the following structure. and are keywords that introduce the names of the volume group and physical volume group,
respectively.
pv_path
...
pv_path
...
pv_path
...
The variables are defined as follows:
pv_path The block device path name of a physical volume within the volume group.
pvg_name The name of the physical volume group. It must be unique within the volume group.
vg_name The path name of the volume group.
EXAMPLES
The following example shows an file containing two volume groups: the first containing two physical volume groups, each with two physical
volumes defined in it; the second containing three physical volume groups, each with one physical volume defined in it.
SEE ALSO
vgcreate(1M), vgextend(1M), vgreduce(1M), vgremove(1M), intro(7), lvm(7).
lvmpvg(4)