We are trying to Establish Network using Linux.Now we are facing the problem in configring Ethernet.In out network we are giving eth0 in server and activating it at the boot time,so it is activating as it is but when we define the Ethernet of node on server and allowing it to activate at boot time... (5 Replies)
I am using Red Hat 7.1 . I have installed one Server and trying to make network installing workstations on other system of a network. The Ethernet of the server has been mounted and working properly. I am getting problem installing /mounting the Ethernet of the workstations .I have tryed this by... (1 Reply)
First time so excuse my ignorance please.
I may not be accurately describing the issue.
I have inherited a small lab mostly SUN V120s.
We lost power and are trying to recover.
Nope no backups...
The primary issue I have is 1 box is an Oracle Server.
It has 2 36Gb harddrives.
I am able to... (3 Replies)
Boot device: /pci@8,600000/SUNW,qlc@4/fp@0,0/disk@w500000e0103c3391,0:a File and args:
SunOS Release 5.8 Version Generic_108528-29 64-bit
Copyright 1983-2003 Sun Microsystems, Inc. All rights reserved.
ifconfig: plumb: qfe2: Bad file number
configuring IPv4 interfaces: eri0.
moving addresses... (1 Reply)
Hello everyone
I have a problem with one server, has Aix 5.3 in the errpt has this message
IDENTIFIER TIMESTAMP T C RESOURCE_NAME DESCRIPTION
F3931284 0105133009 I H ent0 ETHERNET NETWORK RECOVERY MODE
EC0BCCD4 0105133009 T H ent0 ETHERNET DOWN
F3931284 ... (4 Replies)
I have a new Sun 440 and I am trying to configure it. Non of the Ethernet ports are enabled; when I issue "ifconfig -a" it returns nothing. Is there a way to know the available port name (e.g. ce, bge, etc.) by running a command or so ? (4 Replies)
Hi
In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID.
Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Hi,
I have posted several times regarding my application.
In a nutshell, I have a server application that logs attached instrument data over USB and Ethernet. My restriction here is having two wires or more to plug all instrumentation in - at least one for USB and at least one for ethernet.
... (16 Replies)
Discussion started by: fedora18
16 Replies
LEARN ABOUT MOJAVE
locale::codes::langvar
Locale::Codes::LangVar(3pm) Perl Programmers Reference Guide Locale::Codes::LangVar(3pm)NAME
Locale::Codes::LangVar - standard codes for language variation identification
SYNOPSIS
use Locale::Codes::LangVar;
$lvar = code2langvar('acm'); # $lvar gets 'Mesopotamian Arabic'
$code = langvar2code('Mesopotamian Arabic'); # $code gets 'acm'
@codes = all_langvar_codes();
@names = all_langvar_names();
DESCRIPTION
The "Locale::Codes::LangVar" module provides access to standard codes used for identifying language variations, such as those as defined in
the IANA language registry.
Most of the routines take an optional additional argument which specifies the code set to use. If not specified, the default IANA language
registry codes will be used.
SUPPORTED CODE SETS
There are several different code sets you can use for identifying language variations. A code set may be specified using either a name, or
a constant that is automatically exported by this module.
For example, the two are equivalent:
$lvar = code2langvar('en','alpha-2');
$lvar = code2langvar('en',LOCALE_CODE_ALPHA_2);
The codesets currently supported are:
alpha
This is the set of alphanumeric codes from the IANA language registry, such as 'arevela' for Eastern Armenian.
This code set is identified with the symbol "LOCALE_LANGVAR_ALPHA".
This is the default code set.
ROUTINES
code2langvar ( CODE [,CODESET] )
langvar2code ( NAME [,CODESET] )
langvar_code2code ( CODE ,CODESET ,CODESET2 )
all_langvar_codes ( [CODESET] )
all_langvar_names ( [CODESET] )
Locale::Codes::LangVar::rename_langvar ( CODE ,NEW_NAME [,CODESET] )
Locale::Codes::LangVar::add_langvar ( CODE ,NAME [,CODESET] )
Locale::Codes::LangVar::delete_langvar ( CODE [,CODESET] )
Locale::Codes::LangVar::add_langvar_alias ( NAME ,NEW_NAME )
Locale::Codes::LangVar::delete_langvar_alias ( NAME )
Locale::Codes::LangVar::rename_langvar_code ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangVar::add_langvar_code_alias ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangVar::delete_langvar_code_alias ( CODE [,CODESET] )
These routines are all documented in the Locale::Codes::API man page.
SEE ALSO
Locale::Codes
The Locale-Codes distribution.
Locale::Codes::API
The list of functions supported by this module.
http://www.iana.org/assignments/language-subtag-registry
The IANA language subtag registry.
AUTHOR
See Locale::Codes for full author history.
Currently maintained by Sullivan Beck (sbeck@cpan.org).
COPYRIGHT
Copyright (c) 2011-2013 Sullivan Beck
This module is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.18.2 2014-01-06 Locale::Codes::LangVar(3pm)