'Solaris x86 boot single user' for more information.
I don't know why the 'rolemod' command was not found when you tried it. However, try again when in superuser (su) mode with a # prompt.
It should definitely (using Solaris 11) allow you to revert 'root' to a standard account so you can login to it directly. You might need to run
command to set/change the root password (again whilst superuser).
how can i change the superuser password?
the admin left the company, and we want to change the password.
to gain su access, i use:
# su -
password:***** (old password)
then, using passwd command it changes my own login password, not the root??
(this is not trying to block anybody's... (4 Replies)
Hi All,
Oracle 8.0 database is running on SCO-UNIXWARE 7.0 Operating system. Some how ORACLLE DATABASE has crashed. After rebooting the PC only the SUPER USER could login. No other user is able to login.
we need ORACLE user to start the DATABASE again.
It is asking for the password, after... (2 Replies)
My first post:
in /etc/rc2.d i have a startup script: Script1.
if you run #>scirpt1 stop/start from any user other than root you will get u must be supper user to run this script. eventhough the rights are 777.
Question: how can i get my user_a be able to run this script to stop and start it... (2 Replies)
hi All,
In my script I want to run some drop and select statements in the same host as a different user.I am inputting password for the superuser from the user who will be executing the script.
ie ,
I would be greatfull to you experts if you could suggest me how to proceed. (4 Replies)
I have a korn shell script (main.sh) owned by unix account "A". I want to execute certain lines in the script using another user "B" (with user "B" login profile). I need to do this way for multiple lines to be executed using different unix accounts in main.sh.
I was trying to use "su -... (3 Replies)
Hi!
Can someone please tell me how to log-in to Solaris as a superuser or as a root?
I have tried using "root" as a username, and my superuser password i had set in the terminal for the log-in password but it says "Roles can only be assumed by authorized users". "Permission denied."
I'm... (1 Reply)
Hello!
I found this on net:
This is the ``prompt''. If you entered you username, or your password incorrectly, you will be greeted by:
Login incorrect
localhost login: Don't panic, try again. Likely you either mis-typed either your login name, or your password. Try again. You're not... (2 Replies)
I'm trying to add a superuser (admin) to plesk from SSH (I have root access). Can this be done? I have search over the web but did not find any solution to my problem. My version is Plesk 9.3 (0 Replies)
Discussion started by: galford
0 Replies
LEARN ABOUT NETBSD
rtfps
RTFPS(4) BSD Kernel Interfaces Manual RTFPS(4)NAME
rtfps -- multiplexing serial communications interface
SYNOPSIS
rtfps0 at isa? port 0x1230 irq 10
com2 at rtfps0 slave 0
com3 at rtfps0 slave 1
com4 at rtfps0 slave 2
com5 at rtfps0 slave 3
DESCRIPTION
The rtfps driver provides support for IBM RT PC boards that multiplex together up to four EIA RS-232C (CCITT V.28) or RS-422A communications
interfaces.
Each rtfps device is the master device for up to four com devices. The kernel configuration specifies these com devices as slave devices of
the rtfps device, as shown in the synopsis. The port specification for the rtfps device is used to compute the base addresses for the com
subdevices.
FILES
/dev/tty0?
SEE ALSO com(4)HISTORY
The rtfps driver was written by Charles Hannum, based on the ast driver.
BUGS
The rtfps driver is unlikely to work on non-EISA and non-PCI machines. The ISA bus only asserts 10 I/O address lines, and this is not
enough.
Even on EISA and PCI machines, some address conflicts have been observed. On one machine, the second port always conflicted with something
(though it's not clear what) and caused strange results. Disabling the second port in the kernel config allowed the other three ports to
function correctly.
BSD August 7, 1994 BSD