I've just completed a fresh install of HP-UX 11.0 on my 712/80 and everything starts up fine until it gets to the point where X kicks off and I believe at this point is supposed to launch into the CDE login.
It just sits there on the blank X screen with the X cursor for a minute or so then BEEPS... (9 Replies)
I modified the partitions on my Solaris 10 disk using format command in "boot cdrom -s" mode and then tried rebooting with "reboot". It said "Boot load failed".
Why does this happen?
I have faced this error before:( and I went in for a fresh installation of the OS.Can anyone tell me the reason as... (1 Reply)
I've installed AIX 5.1 on a 43p-140, but am unable to log in. At no point in the install did it ask me for a root password. When it boots to the console prompt, I enter "root" as a username, and then after 1 second it cycles right back to another root prompt.
I am accessing the 43p-140... (4 Replies)
Hello,
For whatever reason, after installing Solaris 10 I can ping anything within my own LAN, including the router which is also set as the default gateway, but I have no internet connectivity with it. At first I thought this was a DNS issue, but I can't connect with external IP addresses... (3 Replies)
Hi all
Im rebuilding an 6800 domain with solaris 10. Server is located in a different town and cant be bothered to drive down and install a dvd into its drive.
So, apart from jumpstarting it and using a local DVD, is there a way I can an ISO image to build a new client ?? eg. mount an ISO... (2 Replies)
Good evening all,I'm new to your site, so please bear any infringements or transgressions on my part.I'm new to the whole Solaris boot install over the net scenario, but here's where I'm stuck:I have an M5000 with 2 domains (running unimode). Domain 0 is configured and running Solaris 10. Domain 1... (9 Replies)
Installing Solaris 8 for the first time...on a SunBlade 100. I have original Solaris 8 CD's.
About 45 minutes into the installation, the install halts with the following errors:
ERROR: Could not open file /a/etc/vfstab
ERROR: Could not create the file system mount table /etc/vfstab
I... (4 Replies)
Hi Everyone,
I have been struggling for few days with iSCSI and thought I could get some help on the forum...
fresh install of AIX7.1 TL4 on Power 710, The rootvg relies on 3 SAS disks in RAID 0, 32GB Memory
The lpar Profile is using all of the managed system's resources.
I have connected... (11 Replies)
Hello,
I have downloaded and install debian in computer it is blinking cursor what this mean? (6 Replies)
Discussion started by: Riteshkakkar
6 Replies
LEARN ABOUT DEBIAN
bup-margin
bup-margin(1) General Commands Manual bup-margin(1)NAME
bup-margin - figure out your deduplication safety margin
SYNOPSIS
bup margin [options...]
DESCRIPTION
bup margin iterates through all objects in your bup repository, calculating the largest number of prefix bits shared between any two
entries. This number, n, identifies the longest subset of SHA-1 you could use and still encounter a collision between your object ids.
For example, one system that was tested had a collection of 11 million objects (70 GB), and bup margin returned 45. That means a 46-bit
hash would be sufficient to avoid all collisions among that set of objects; each object in that repository could be uniquely identified by
its first 46 bits.
The number of bits needed seems to increase by about 1 or 2 for every doubling of the number of objects. Since SHA-1 hashes have 160 bits,
that leaves 115 bits of margin. Of course, because SHA-1 hashes are essentially random, it's theoretically possible to use many more bits
with far fewer objects.
If you're paranoid about the possibility of SHA-1 collisions, you can monitor your repository by running bup margin occasionally to see if
you're getting dangerously close to 160 bits.
OPTIONS --predict
Guess the offset into each index file where a particular object will appear, and report the maximum deviation of the correct answer
from the guess. This is potentially useful for tuning an interpolation search algorithm.
--ignore-midx
don't use .midx files, use only .idx files. This is only really useful when used with --predict.
EXAMPLE
$ bup margin
Reading indexes: 100.00% (1612581/1612581), done.
40
40 matching prefix bits
1.94 bits per doubling
120 bits (61.86 doublings) remaining
4.19338e+18 times larger is possible
Everyone on earth could have 625878182 data sets
like yours, all in one repository, and we would
expect 1 object collision.
$ bup margin --predict
PackIdxList: using 1 index.
Reading indexes: 100.00% (1612581/1612581), done.
915 of 1612581 (0.057%)
SEE ALSO bup-midx(1), bup-save(1)BUP
Part of the bup(1) suite.
AUTHORS
Avery Pennarun <apenwarr@gmail.com>.
Bup unknown-bup-margin(1)