My experience is with older stuff but this is what was required:
Since there is no hardware link to a new device the first step is to create it"
which creates the link in /dev
Then create the identity for the file systems you want on it:
In my case
creating names and sizes
And last, creating the file system(s) and mount points:
In my case
for each file system you created earlier. My systems had provisions for the formatting and mounting conditions as part of this. Since you are doing this for a removable unit you wouldn't want to automatically mount it unless you are planning to reboot each time you make a change.
i have a Simple Tech hard drive that i use between two computers. it is formatted to ntfs. i have a dell desktop with Ubuntu 7.10 and Ubuntu 8.04 and Windows XP Home. and i have a laptop with Ubuntu 7.10 and Ubuntu 8.04. the laptop recognizes the hard drive on both 8.04 and 7.10 but my desktop... (9 Replies)
Can anyone please walk me through how to mount an external parallel (or scsi) hard drive in visualize C3000 machine? I also would like to mount "/var/sallie" directory in that external drive. My "/var/sallie" directory is running out of space so I would like to mount an external hard drive so that... (0 Replies)
Hi-
I would like to know if anyone has used any USB External Hard Drive, about 500/750GB or 1TB, with any of the Solaris 10 "SPARC" systems. Not on intel nor amd platform.
I'm looking for the compatible drive and found a few listed on Sun solaris ready page, but I'd like to have inputs from... (3 Replies)
Guys,
I have googled and checked this forum in detail and couldn't find any satisfactory answers for my problem.
I am trying to connect a external SCSI hard Drive(Sea Gate) to a Ultra 80.
I connected it powered it up and at OK prompt did : boot -r
system comes up and complains about not... (6 Replies)
Hi Folks,
First a little background, I am working on a ship that operates in the Indian Ocean and Persian/Arabian gulf area. We had a Sunblade 2000 that finally died. The Video board burned up and I guess damaged the mother board. So we ordered 2 rebuilt 2000s one as a spare. Due to mounting... (1 Reply)
Hello
I have a new project being kicked off next month and i should learn UNIX fast. I have never used UNIX before so i have the following questions:
1) Is any UNIX free to install?
2) Can i install and boot UNIX from an External Hard Drive (The system board on my laptop crashed so i took the... (2 Replies)
Hi Guys..
I want to install Linux on my portable hard drive.
I created a 20GB partition in my hard drive for linux, Now I want to make it bootable mean when I connect it to system n start the system it will start the LINUX and when start without usb-hard drive it should start the windows.
... (3 Replies)
Discussion started by: atul9806
3 Replies
LEARN ABOUT SUSE
hd
HD(4) Linux Programmer's Manual HD(4)NAME
hd - MFM/IDE hard disk devices
DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major
device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave
hdd.
General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the
partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order
the partitions are discovered, and only nonempty, nonextended partitions get a number. However, partition numbers 1-4 are given to the
four partitions described in the MBR (the "primary" partitions), regardless of whether they are unused or extended. Thus, the first logi-
cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions
on an IDE disk.
For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS "primary" partition on the
second one.
They are typically created by:
mknod -m 660 /dev/hda b 3 0
mknod -m 660 /dev/hda1 b 3 1
mknod -m 660 /dev/hda2 b 3 2
...
mknod -m 660 /dev/hda8 b 3 8
mknod -m 660 /dev/hdb b 3 64
mknod -m 660 /dev/hdb1 b 3 65
mknod -m 660 /dev/hdb2 b 3 66
...
mknod -m 660 /dev/hdb8 b 3 72
chown root:disk /dev/hd*
FILES
/dev/hd*
SEE ALSO chown(1), mknod(1), sd(4), mount(8)COLOPHON
This page is part of release 3.25 of the Linux man-pages project. A description of the project, and information about reporting bugs, can
be found at http://www.kernel.org/doc/man-pages/.
Linux 1992-12-17 HD(4)