03-01-2017
Could be many things. The configuration from the Unix side looks fine, but have your considered:-
- A physical link issue
- not connected to right switch
- faulty or disabled port on the NIC
- faulty or disabled port on the switch
- faulty cable
- Configuration on the switch making the port part of a different VLAN
- Routing error on the switch
- Something else?
10 More Discussions You Might Find Interesting
1. IP Networking
We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command
64 bytes from 124.168.215.40:... (6 Replies)
Discussion started by: chrisanto_2000
6 Replies
2. IP Networking
Hello this is my first post at this forum.
Apologize for my lack of network understanding
but Im posting to learn.
I have a problem reaching default gateway 10.18.110.1
If I use my laptop I can ping 10.18.110.1 but with our red hat multihomed server the gateway does not respond to ping.
cat... (11 Replies)
Discussion started by: vettec3
11 Replies
3. Solaris
I was install new solaris10 on m4000 model after that i "ping -s" to default gateway but it's take longtime (2 Min) to reply and if i use "ping" only it's reply to fase(2 sec). any body who can tell me about my problem and how to fix it please. i'm try to fix several days. (2 Replies)
Discussion started by: cesmk
2 Replies
4. AIX
Hello,
I am new to Unix :D and have been trying to configure an AIX server running 5.3. I used smitty or smit to configure interface 0 on the server. I am able to ping the IP I set, however I am still unable to ping the gateway. I configured the IP by navigating to Communications Applications... (6 Replies)
Discussion started by: cdub50
6 Replies
5. Red Hat
I know the subject line is very similar to: destination host unreachable
but the problem with my machine appears to be somewhat different from that thread. apologies if I missed something from there.
We recently moved a machine physically and from one subnet to another . I used... (1 Reply)
Discussion started by: mirage
1 Replies
6. UNIX for Dummies Questions & Answers
I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a... (4 Replies)
Discussion started by: Rutgerncas
4 Replies
7. AIX
I just reinstalled a fresh install of 5300 07 on an old 44p model 170, after installing I set an IP Address on en2 and I tried to the ping default gateway, no response. I tried a
startsrc -g tcpip
... and then I can ping the default gateway. I broke the ping and tried again to ping. I cannot... (1 Reply)
Discussion started by: asyed123
1 Replies
8. Red Hat
Hi,
Here is the issue: There are 2 identical systems in the same subnet here. They can ping and ssh each other. One can ping the default gateway and one can not with error '... icmp_seq Destination Host Unreachable'. I can't find any difference between the two systems in terms of network... (4 Replies)
Discussion started by: aixlover
4 Replies
9. AIX
Hi,
I installed AIX 7.1 on a blade though (hmc with vio). I can ping the IP address, but not the gateway. Is there anything that I should configure?
Is there anything that I have to check with vio setting or Am I missing any configuration?
Please let me know further.
Thank you (5 Replies)
Discussion started by: pjeedu2247
5 Replies
10. UNIX for Beginners Questions & Answers
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
LEARN ABOUT CENTOS
rescan-scsi-bus.sh
RESCAN-SCSI-BUS.SH(1) User Commands RESCAN-SCSI-BUS.SH(1)
NAME
rescan-scsi-bus.sh - script for adding and removing SCSI devices without rebooting
SYNOPSIS
rescan-scsi-bus.sh [options] [host [host ...]]
OPTIONS
-a, --alltargets
scan all targets, not just currently existing [default: disabled]
-d enable debug [default: 0]
-l activates scanning for LUNs 0--7 [default: 0]
-L NUM activates scanning for LUNs 0--NUM [default: 0]
-w, --wide
scan for target device IDs 0--15 [default: 0--7]
-c enables scanning of channels 0 1 [default: 0 / all detected ones]
-r, --remove
enables removing of devices [default: disabled]
-f, --flush
flush failed multipath devices [default: disabled]
-i, --issue-lip
issue a FibreChannel LIP reset [default: disabled]
-u, --update
look for existing disks that have been remapped
-s, --resize
look for resized disks and reload associated multipath devices, if applicable
--forcerescan
rescan existing devices
--forceremove
remove and readd every device (DANGEROUS)
--nooptscan
don't stop looking for LUNs is 0 is not found
--color
use coloured prefixes OLD/NEW/DEL
--hosts=LIST
scan only host(s) in LIST
--channels=LIST
scan only channel(s) in LIST
--ids=LIST
scan only target ID(s) in LIST
--luns=LIST
scan only lun(s) in LIST
--sync, --nosync
issue a sync / no sync [default: sync if remove]
--attachpq3
tell kernel to attach sg to LUN 0 that reports PQ=3
--reportlun2
tell kernel to try REPORT_LUN even on SCSI2 devices
--largelun
tell kernel to support LUNs > 7 even on SCSI2 devs
--sparselun
tell kernel to support sparse LUN numbering
Host numbers may thus be specified either directly on cmd line (deprecated) or or with the --hosts=LIST parameter (recommended).
LIST: A[-B][,C[-D]]... is a comma separated list of single values and ranges (No spaces allowed.)
SEE ALSO
rescan-scsi-bus.sh Homepage: http://www.garloff.de/kurt/linux/#rescan-scsi
sg3_utils Homepage: http://sg.danny.cz/sg
rescan-scsi-bus.sh 1.57 leden 2014 RESCAN-SCSI-BUS.SH(1)