03-01-2017
Could be many things. The configuration from the Unix side looks fine, but have your considered:-
- A physical link issue
- not connected to right switch
- faulty or disabled port on the NIC
- faulty or disabled port on the switch
- faulty cable
- Configuration on the switch making the port part of a different VLAN
- Routing error on the switch
- Something else?
10 More Discussions You Might Find Interesting
1. IP Networking
We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command
64 bytes from 124.168.215.40:... (6 Replies)
Discussion started by: chrisanto_2000
6 Replies
2. IP Networking
Hello this is my first post at this forum.
Apologize for my lack of network understanding
but Im posting to learn.
I have a problem reaching default gateway 10.18.110.1
If I use my laptop I can ping 10.18.110.1 but with our red hat multihomed server the gateway does not respond to ping.
cat... (11 Replies)
Discussion started by: vettec3
11 Replies
3. Solaris
I was install new solaris10 on m4000 model after that i "ping -s" to default gateway but it's take longtime (2 Min) to reply and if i use "ping" only it's reply to fase(2 sec). any body who can tell me about my problem and how to fix it please. i'm try to fix several days. (2 Replies)
Discussion started by: cesmk
2 Replies
4. AIX
Hello,
I am new to Unix :D and have been trying to configure an AIX server running 5.3. I used smitty or smit to configure interface 0 on the server. I am able to ping the IP I set, however I am still unable to ping the gateway. I configured the IP by navigating to Communications Applications... (6 Replies)
Discussion started by: cdub50
6 Replies
5. Red Hat
I know the subject line is very similar to: destination host unreachable
but the problem with my machine appears to be somewhat different from that thread. apologies if I missed something from there.
We recently moved a machine physically and from one subnet to another . I used... (1 Reply)
Discussion started by: mirage
1 Replies
6. UNIX for Dummies Questions & Answers
I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a... (4 Replies)
Discussion started by: Rutgerncas
4 Replies
7. AIX
I just reinstalled a fresh install of 5300 07 on an old 44p model 170, after installing I set an IP Address on en2 and I tried to the ping default gateway, no response. I tried a
startsrc -g tcpip
... and then I can ping the default gateway. I broke the ping and tried again to ping. I cannot... (1 Reply)
Discussion started by: asyed123
1 Replies
8. Red Hat
Hi,
Here is the issue: There are 2 identical systems in the same subnet here. They can ping and ssh each other. One can ping the default gateway and one can not with error '... icmp_seq Destination Host Unreachable'. I can't find any difference between the two systems in terms of network... (4 Replies)
Discussion started by: aixlover
4 Replies
9. AIX
Hi,
I installed AIX 7.1 on a blade though (hmc with vio). I can ping the IP address, but not the gateway. Is there anything that I should configure?
Is there anything that I have to check with vio setting or Am I missing any configuration?
Please let me know further.
Thank you (5 Replies)
Discussion started by: pjeedu2247
5 Replies
10. UNIX for Beginners Questions & Answers
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
LEARN ABOUT DEBIAN
ecaccess-association-delete
ECACCESS-ASSOCIATION-DELETE(1p) User Contributed Perl Documentation ECACCESS-ASSOCIATION-DELETE(1p)
NAME
ecaccess-association-delete - Delete Association
SYNOPSIS
ecaccess-association-delete -version|-help|-manual
ecaccess-association-delete [-debug] [-gateway name] association-name
DESCRIPTION
Allow deleting an ECtrans Association. Once deleted the Association can not be retrieved. The History associated with this Association will
also be removed from the ECaccess Gateway Database.
ARGUMENTS
association-name
The name of the Association to delete.
OPTIONS
-gateway name
This is the name of the ECaccess Gateway where the Association is installed. It is by default the Gateway you are connected to. In
order to get the name of your current Gateway you can use the ecaccess-gateway-name command. When using the commands at ECMWF the
default Gateway is always "ecaccess.ecmwf.int".
-version
Display version number and exits.
-help Print a brief help message and exits.
-manual Prints the manual page and exits.
-debug Display the SOAP messages exchanged.
EXAMPLES
ecaccess-association-delete -gateway ecaccess.ecmwf.int test
Remove the test Association on the ecaccess.ecmwf.int Gateway.
ecaccess-association-delete test2
Remove the test2 Association on the default Gateway.
SEE ALSO
ecaccess-association-get, ecaccess-association-list, ecaccess-association-protocol, ecaccess-association-put and ecaccess.
perl v5.14.2 2012-04-16 ECACCESS-ASSOCIATION-DELETE(1p)