Thanks much. It was very helpful.
I booted from RAID Management DVD and ran "arcconf DELETE 1 LOGICALDRIVE ALL"
That wiped out installed OS also, which is OK for me. I am booting from Solaris 11 OS DVD now, but it says "OS can not be installed on any of the disks". I checked in "shell" and it doesn't see any disk now ---------- Post updated at 09:27 PM ---------- Previous update was at 09:19 PM ----------
We used kstat on netra240/440 to check if the link is full duplex. So we do something like:
bash-3.00# kstat -pc net bge:1::/'link_duplex'/ | cut -f2
2
The output 2 indicates the link is full duplex. This kind of check worked all right for Netra 240/440 systems.
However, the nxge... (2 Replies)
I 've 2 different T5220 and both are showing different prompts when i ssh to the console.
1. Shows sc> ALOM
2. Shows -> ILOM
as far as i know the T5220 comes with ILOM , so why i 'm seeing 2 different type of console for same tyep of hardware ?
and i found that we... (6 Replies)
Hi,
SC on one of my T5220 is not responding .. it does not show not let me type anything .. what could be the reason for it ? though when i powercycle the box from sc it shows me the system coming up but after that does not let me login thru sc
sc> console -f
Enter #. to return to ALOM. (2 Replies)
We're just about to migrate a large application from an Enterprise 6900 to a pair of T5220s utilising LDOMs. Does anyone have any experience of LDOMs on this kit and can provide any recommendations or pitfalls to avoid?
I've heard that use of LDOMs can have an impact on I/O speeds as it's all... (9 Replies)
Hi,
We have two T5220 servers in our datacentre
one server is showing 64 processors online
and another showing 32 processors online
two are newly purchased, there is no hardware faults in this server
one server has 64gb memory and it shows 64 processors,
and other having 32gb memory and it... (5 Replies)
I have a new T5220 racked at our remote office and the guys who racked it does not know how to configure the SP on the system .. is there any way i can do it remotely ? (1 Reply)
I'm trying to use a V210 (sun4u) configured as a jumpstart server to flash install a number of T5220's (sunv4).
The Facts:
V210 - Solaris 10 (September 2010 Release / not patched)
T5220's - Archive's created using prior (unknown) version of solaris 10.
Flar -i <archive name> shows the... (6 Replies)
Hi Guys and Gals,
Wondering if anyone could help me, tricky one this.
Got a T5220 with a graphics card. When you power it on, it outputs its output to the screen and you can type commands with the keyboard etc.
But no matter what version of Solaris 10 you use, when you do a boot cdrom... (1 Reply)
Hello guys,
can anyone give me some advice on how to perform
clean installation of Solaris 10 on T5220 ?
I am connected with serial management port on the machine,
i have the ok promt and now i should eject the dvdrom to insert
Solaris dvd into and start the clean install.
So how to do that... (3 Replies)
We have one box T5220 which was assigned 2x100G Luns but i have a strange problem if i use powermt display it only shows me one card but cfgadm, fcinfo commands shows 2 dual port cards as up. What could be the reason for it. I already did a re-configure reboot but that didn't help. Can anyone help... (1 Reply)
Discussion started by: fugitive
1 Replies
LEARN ABOUT NETBSD
pdcide
PDCIDE(4) BSD Kernel Interfaces Manual PDCIDE(4)NAME
pdcide -- Promise IDE disk controllers driver
SYNOPSIS
pdcide* at pci? dev ? function ? flags 0x0000
DESCRIPTION
The pdcide driver supports the Promise Ultra33, Ultra66, Ultra100, Ultra100TX2, Ultra100TX2v2, Ultra133, Ultra133TX2, Ultra133TX2v2, Fast-
trak133 and Serial ATA/150 IDE controllers, and provides the interface with the hardware for the ata(4) driver.
The 0x0002 flag forces the pdcide driver to disable DMA on chipsets for which DMA would normally be enabled. This can be used as a debugging
aid, or to work around problems where the IDE controller is wired up to the system incorrectly.
SEE ALSO ata(4), atapi(4), intro(4), pci(4), pciide(4), wd(4), wdc(4)BUGS
The timings used for the PIO and DMA modes for controllers listed above are for a PCI bus running at 30 or 33 MHz. This driver may not work
properly on overclocked systems.
The pdcide driver does NOT function correctly on NetBSD/sparc64.
BSD December 23, 2003 BSD