HP C8000 with HP-UX 10.20 Post: 302984854

Sponsored Content

Operating Systems HP-UX HP C8000 with HP-UX 10.20 Post 302984854 by darkox on Tuesday 1st of November 2016 11:05:04 AM

11-01-2016

Registered User

Thank you for reply, vbe,

Just a bit more information about my case.

I am currently using B2600 box which has PA-8600 64bit processor with multiple PCI interface cards, Ultra 2 SCSI hard drive and even IDE CD-ROM and USB. I built that box using the same installation disk (ACE 5 with 1994 ISL) with no problem.

For this reason I do not want to believe it is something to do with 64bit compatibility. However, it seems these boxes using different SCSI controllers, B2600 is using Ultra 2 SCSI LVD while C8000 Ultra 320 SCSI... Might this be an issue?

Regards,

D.

Last edited by darkox; 11-01-2016 at 12:34 PM..

darkox

View Public Profile for darkox

Find all posts by darkox

2 More Discussions You Might Find Interesting

1. HP-UX

HP UX 11i and HP C8000

Hey, i want install HP UX 11i on HP C8000. When i start the C8000 i get a prompt. On this Prompt i write BOot P1 P1 is my DVD-ROM (IDE). I get the Message "ERROR: Not a boot path". When i write SEArch the Prompt said: P0 scsiA.6 HP73.4MAT3073NP P1 ide.1 ...

2. HP-UX

Help needed HP UX 11.11i new install on C8000 Desktop messaging system error CAN'T FIX

Hi, I have a HP UX C8000 box , have installed 11.11i from 4 x cds numerous times to try to get a functioning Network or to try and get rid of this error on start up, after new install and 1st startup I get an error "The desktop messaging system could not be started" and then advice about...

LEARN ABOUT NETBSD

cmdide

CMDIDE(4)						   BSD Kernel Interfaces Manual 						 CMDIDE(4)

NAME

     cmdide -- CMD Technology and Silicon Image IDE disk controllers driver

SYNOPSIS

     cmdide* at pci? dev ? function ? flags 0x0000
     options PCIIDE_CMD064x_DISABLE
     options PCIIDE_CMD0646U_ENABLEUDMA

DESCRIPTION

     The cmdide driver supports the CMD Technology PCI0640, PCI0643, PCI0646, PCI0648, PCI0649, and Silicon Image 0680 IDE controllers, and pro-
     vides the interface with the hardware for the ata(4) driver.

     The 0x0002 flag forces the cmdide driver to disable DMA on chipsets for which DMA would normally be enabled.  This can be used as a debugging
     aid, or to work around problems where the IDE controller is wired up to the system incorrectly.

SEE ALSO

     ata(4), atapi(4), intro(4), pci(4), pciide(4), wd(4), wdc(4)

BUGS

     There's no way to reliably know if a PCI064x controller is enabled or not.  If the driver finds a PCI064x, it will assume it is enabled
     unless the PCIIDE_CMD064x_DISABLE option is specified in the kernel config file.  This will be a problem only if the controller has been dis-
     abled in the BIOS and another controller has been installed and uses the ISA legacy I/O ports and interrupts.

     The PCI0646U controller is known to be buggy with Ultra-DMA transfers, so Ultra-DMA is disabled by default for this controller.  To enable
     Ultra-DMA, use the PCIIDE_CMD0646U_ENABLEUDMA option.  Ultra-DMA can eventually be disabled on a per-drive basis with config flags, see
     wd(4).

     The timings used for the PIO and DMA modes for controllers listed above are for a PCI bus running at 30 or 33 MHz.  This driver may not work
     properly on overclocked systems.

BSD
								 December 13, 2003							       BSD