Our shops server runs SCO Openserver 5 release 5. It has two network cards in it (one on 10.0.0.6 and one on 90.0.0.99). When I run scoadmin and look at the network settings it show both my 3com network cards and a loop back driver http://theentertainer.com/james/untitled.jpg
Can anyone tell... (1 Reply)
I have got a Sco Unix Server, i want to connect some windows workstations. What configurations do i need to make on server and or workstation? (1 Reply)
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
Hello Guys,
We have an old PC running on SCO Unix V. Is there any sites where i can get manual/procedures on how to install and configure Network. Thanks (2 Replies)
hello
i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 )
what i need to do after the new adapter installed on the machine?
thanks
best regards
ariec (1 Reply)
When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command:
entstat -all ent#|grep -i priority
Priority: 5 Active: False
How to make Active to True? (1 Reply)
Hi All,
I am new here - this is my first post.
I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Hi All
I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached.
I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network... (8 Replies)
hi
i installed sco unix open server 5.0.7 on virtual machine vmware and runing it,
its work perfect and good.
now how i can configuare network at scoadmin that i able to access nework ?
---------- Post updated at 08:56 AM ---------- Previous update was at 01:47 AM ----------
nobody can... (2 Replies)
Hello community, I have a Proliant HP DL380P with the following network adapters:
NetXtreme BCM5719 Gigabit Ethernet PCIe (Ethernet 1Gb 4-port 331FLR Adapter)
82580 Gigabit Network Connection (NC365T 4-port Ethernet Server Adapter)
I installed Red Hat 7.2 but it recognizes only the... (9 Replies)
Discussion started by: Lord Spectre
9 Replies
LEARN ABOUT DEBIAN
ra_pict
RA_PICT(1) General Commands Manual RA_PICT(1)NAME
ra_pict - convert Radiance pictures to Macintosh PICT files
SYNOPSIS
ra_pict [ -e +/- stops ] [ -v ] [ -g gamma ] [ infile [ outfile ]]
DESCRIPTION
Ra_pict converts a Radiance picture, as produced by rpict (1) to a Macintosh PICT file. The picture will be a 24 bit PICT 2 picture, using
a single bit map (DirectRect).
OPTIONS -g gamma This sets an explict gamma correction for the image. If it is not specified, the default value of 2.0 is used.
-v Invokes verbose mode, and gives line on standard error giving the size of the picture and the gamma correction used.
-e +/- stops
Adjusts the exposure by stops.
infile Specifies the file to read the picture from. If none is specified, it takes it from standard input. If standard input is used,
then the picture is sent to standard output.
outfile Specifies the file to send the PICT file to. If none is specified, it is sent to standard output.
EXAMPLES
ra_pict mypict.hdr mypict.pict
Will convert the Radiance picture mypict.hdr, giving the Macintosh PICT mypict.pict.
ra_pict -g 2.2 mypict.hdr mypict.pict
Will convert the file using a gamma of 2.2.
SEE ALSO rpict(1)BUGS
Does not yet do Macintosh PICT to Radiance PIC, as this PICT files are a lot more complex than just one bit map. This is left as an exer-
cise for the reader :-)
AUTHOR
Russell Street
RADIANCE 11/15/93 RA_PICT(1)