Finally, the solution for this was to kill the 2 httpd processes listed from the lsof command :
After killing these 2 processes, all the CLOSE_WAIT connections were gone.
Then, I could restart the apache process once again.
I am not by any means a UNIX guru if you can't already tell by the question I'm about to ask.
How do I launch Apache web server on my SOlaris 8 server without rebooting it?
Any help would be much appreciated!!!
-Thanks (5 Replies)
I successfully installed Apache, but When I tried to start it I experienced problems.
After installing and compiling, I typed the PREFIX "usr/local/
apache/bin/apachect1 start." The output was path not found.
After checking the apachect1 file using vi, I found the file empty.
There was no... (4 Replies)
Hi All,
I am trying to start the docbase but i am getting the following error-:
$ ./dm_start_ncsglorbiprd00
interpreter "/bin/sh" not found
file link resolves to "/usr/bin/sh"
sh: ./dm_start_ncsglorbiprd00: not found.
Can anyone please help me in this regard.
Thanks in advance
... (0 Replies)
I've been working on a project to replace one of the my group's primary NIS servers. It also runs mysql and apache, as it is the host for the our team's hardware tracking database and website. Its running apache 1.3, and for some odd reason, I can't get apache to start on system boot. The... (1 Reply)
I just installed Apache 2.2.6 & when trying to start it i got this:
Invalid command 'SSLProtocol', perhaps misspelled or defined by a module not included in the server configuration
Any help? (3 Replies)
Hi,
I just installed Apache 2.0.54 and when I try and start httpd I get
mohit@mohit-desktop:/sw/pkg/apache/bin$ ./httpd -k start
httpd: Could not determine the server's fully qualified domain name, using 127.0.1.1 for ServerName
(13): make_sock: could not bind to address :80
no listening... (1 Reply)
Sir,
I have installed an Apache server in Fedora 9 (packages)
and when i go to etc folder and try the command
httpd -k start
it says command not found....can any one help me out!!!
---------- Post updated at 12:02 PM ---------- Previous update was at 11:46 AM ----------
When i... (4 Replies)
Hello,
I am facing an issue while starting the apache server after compiling php and curl.
Below are the versions i am using.
php-5.2.17
httpd-2.2.17
curl-7.16.0
CentOS5.5x64
Compiling above packages without curl working very fine but when trying to compile php with curl below error is... (1 Reply)
e.g.
File name: File.txt
cat File.txt
Result:
#INBOUND_QUEUE=FAQ1
INBOUND_QUEUE=FAQ2
I want to get the value for one which is not commented out.
Thanks, (3 Replies)
Discussion started by: Tanu
3 Replies
LEARN ABOUT FREEBSD
upsd.conf
UPSD.CONF(5) NUT Manual UPSD.CONF(5)NAME
upsd.conf - Configuration for Network UPS Tools upsd
DESCRIPTION
upsd uses this file to control access to the server and set some other miscellaneous configuration values. This file contains details on
access controls, so keep it secure. Ideally, only the upsd process should be able to read it.
CONFIGURATION DIRECTIVES
"MAXAGE seconds"
upsd usually allows a driver to stop responding for up to 15 seconds before declaring the data "stale". If your driver takes a very
long time to process updates but is otherwise operational, you can use MAXAGE to make upsd wait longer.
Most users should leave this at the default value.
"STATEPATH path"
Tell upsd to look for the driver state sockets in path rather than the default that was compiled into the program.
"LISTEN interface port"
Bind a listening port to the interface specified by its Internet address. This may be useful on hosts with multiple interfaces. You
should not rely exclusively on this for security, as it can be subverted on many systems.
Listen on TCP port port instead of the default value which was compiled into the code. This overrides any value you may have set with
configure --with-port. If you don't change it with configure or this value, upsd will listen on port 3493 for this interface.
Multiple LISTEN addresses may be specified. The default is to bind to 127.0.0.1 if no LISTEN addresses are specified (and ::1 if IPv6
support is compiled in).
LISTEN 127.0.0.1
LISTEN 192.168.50.1
LISTEN ::1
LISTEN 2001:0db8:1234:08d3:1319:8a2e:0370:7344
This parameter will only be read at startup. You'll need to restart (rather than reload) upsd to apply any changes made here.
"MAXCONN connections"
This defaults to maximum number allowed on your system. Each UPS, each LISTEN address and each client count as one connection. If the
server runs out of connections, it will no longer accept new incoming client connections. Only set this if you know exactly what you're
doing.
"CERTFILE certificate file"
When compiled with SSL support, you can enter the certificate file here. The certificates must be in PEM format and must be sorted
starting with the subject's certificate (server certificate), followed by intermediate CA certificates (if applicable_ and the highest
level (root) CA. It should end with the server key. See docs/security.txt or the Security chapter of NUT user manual for more
information on the SSL support in NUT.
SEE ALSO upsd(8), nutupsdrv(8), upsd.users(5)INTERNET RESOURCES
The NUT (Network UPS Tools) home page: http://www.networkupstools.org/
Network UPS Tools 05/21/2012 UPSD.CONF(5)