Sponsored Content
Operating Systems Solaris Using a Modem on a T5-2 or a T5240 Post 302969392 by hicksd8 on Tuesday 22nd of March 2016 08:09:29 AM
Old 03-22-2016
Are you sure that the (legacy) zone would run the device drivers?

Aren't all devices/peripherals driven by the global zone with any non-global zones being given access via the global? Like with ethernet interfaces, the legacy zone either has exclusive or shared access to the network adapter but the global runs the driver.

I'm assuming that access to a USB or serial port would depend on whether the non-global zone has the device mapped (in /dev) and then whether the global allows the access, assuming the device is not already in use.

Perhaps other forum members may know the specifics.
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Modem - Test /dev/modem

Ok. I tried following the directions from some of the other threads, but I've hit a road block. I have red hat 7.3 and I installed the hcf package: hcfpcimodem-0.99lnxtbeta03042700k2.4.18_3-1rh.i386.rpm It installed ok, no errors, but I still can't get linux to find my modem. I've tried... (2 Replies)
Discussion started by: lawadm1
2 Replies

2. Solaris

raidctl on SUN T5240

Setting up a T5240 with two disks c1t0d0 and c1t1d0. I am trying to use raidctl but when I issue. raidctl -l I get Controller 1 Disk: 0.0.0 Disk: 0.1.0 So I try raidctl -c '0.0.0 0.1.0' -r 1 1 and I get "Array in use." I try (4 Replies)
Discussion started by: photon
4 Replies

3. Solaris

cannot plumb nxge on T5240

its a fresh installation. during the OS setup, it did not prompt for IP, netmask and gateway. using Solaris 10 08/07 update 4. I tried to plumb manually but encountered no such interface error. but nxge interfaces can be greped from the /etc/path_to_inst file. getting similar error on... (3 Replies)
Discussion started by: incredible
3 Replies

4. Solaris

SUN T5240 vs M3000

Hi, We are planning to buy new server for our data center. Sun T5240 or M3000 which one have better performance, we are going to create many dt sessions in this server. So, i need your suggestions. RJS (4 Replies)
Discussion started by: rajasekg
4 Replies

5. Solaris

ufsrestore T5240

Hi Friends we have sun T5240 server, we have taken ufsdump of this server remotely with scsi tapedrive, If we need to do ufsrestore means what we have to do, since T5240 has not having scsi port, any procedure is there? Regards Rajasekar (5 Replies)
Discussion started by: rajasekg
5 Replies

6. Solaris

Bizarre Sun T5240 behavior

Hi - I have a T5240 with 7 LDOMS configured. One night, network comm was broken somehow. Nobody was doing anything on the machine at the time. Here is what I saw in messages: WARNING: nxge3 : nxge_dma_mem_alloc: ddi_dma_mem_alloc kmem alloc failed WARNING: nxge3 : nxge_alloc_rx_buf_dma:... (2 Replies)
Discussion started by: pyroman
2 Replies

7. Solaris

Disable multithreading option on T5240

Hi Gurus Can any one tell me the process of disabling the multithreading option on T5240 server and my OS is on LDOM, having one physical processor with 8 core & 8 thread per core Regards (3 Replies)
Discussion started by: amity
3 Replies

8. Solaris

Cannot configure RAID on T5240

Hi ! I've been given a T5240 with 4 disks and 2 HBA cards (but no array connected). I did a factory reset on SP and NVRAM clean on OBP because the server had been used before. I boot cdrom in single mode and try to create a hw mirror with disks from c1... but only c2 is seen by raidctl. ... (2 Replies)
Discussion started by: delavega
2 Replies

9. Solaris

Question: # of ldoms on T5240 with 2 T2 US 8 core

I have a T5240 with 2 T2 US 8 core.. Theoretically how many ldoms can I configure? (5 Replies)
Discussion started by: Iftikhar Barrie
5 Replies
rem_drv(1M)															       rem_drv(1M)

NAME
rem_drv - remove a device driver from the system SYNOPSIS
rem_drv [-b basedir] device_driver The rem_drv command informs the system that the device driver device_driver is no longer valid. If possible, rem_drv unloads device_driver from memory. rem_drv also updates the system driver configuration files. If rem_drv has been executed, the next time the system is rebooted it automatically performs a reconfiguration boot (see kernel(1M)). The following options are supported: -b basedir Sets the path to the root directory of the diskless client. Used on the server to execute rem_drv for a client. The client machine must be rebooted to unload the driver. Note - The root file system of any non-global zones must not be referenced with the -b option. Doing so might damage the global zone's file system, might compromise the security of the global zone, and might damage the non-global zone's file system. See zones(5). Example 1: Removing the sd Driver The following example removes the sd driver from use: example% rem_drv sd Example 2: Removing a Diskless Client The following example removes the driver from the sun1 diskless client. The driver is not uninstalled or unloaded until the client machine is rebooted. example% rem_drv -b /export/root/sun1 sd Note the caveat on the use of the -b option in the description of that option, above. See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcsu | +-----------------------------+-----------------------------+ add_drv(1M), kernel(1M), update_drv(1M), attributes(5), devfs(7FS) 6 Apr 2005 rem_drv(1M)
All times are GMT -4. The time now is 09:47 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy