02-03-2016
Physical path of NIC/HBA
How can I get the physical path i.e. slot#, port# etc. using a command on linux physical server? Looking for a command for mapping.
thanks...
9 More Discussions You Might Find Interesting
1. Solaris
Hi there
Now, Ive always support servers that used multi path software with dual cards, e.g. powerpath (emc ) / MPXIO. I got asked a question today, that if a solaris 8/9/10 host had 2 HBA cards, but no multipathing software, what would happen ?? Does the HBA card with the highest id on the... (2 Replies)
Discussion started by: sbk1972
2 Replies
2. Solaris
Hi All,
I'm actually trying to configure a Qlogic HBA on a solaris9 connecting in a Brocade SAN. I installed Solaris9 and now trying to look at FC devices..
bash-2.05# luxadm -e port
Found path to 0 HBA ports
bash-2.05# luxadm probe
No Network Array enclosures found in /dev/es... (7 Replies)
Discussion started by: ilan
7 Replies
3. AIX
Hello All,
Can anybody please tell me what is the maximum limit of Physical IBM Power Machine which can be handled by single HMC at a single point of time?
Thanks,
Jenish (1 Reply)
Discussion started by: jenish_shah
1 Replies
4. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
5. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
6. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
7. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
8. Shell Programming and Scripting
sometime the user gives me the Linux NAS path URL which is accessible usings windows explorer like below:
This URL translates to the below physical path on Linux host
Below is what I wish to achieve:
1. Detect if the path provided is NAS URL starting with "\" or a Physical Linux path... (7 Replies)
Discussion started by: mohtashims
7 Replies
9. UNIX for Advanced & Expert Users
Dear all,
I have a remote CentOS7 server that has two network cards. Each card has four ports and port one of card one was defined with the IP address assigned to the server. So far, so good and it's been working for over a year. We have now got cables sorted out so there are four paths... (4 Replies)
Discussion started by: rbatte1
4 Replies
LEARN ABOUT HPUX
pvremove
pvremove(1M) pvremove(1M)
NAME
pvremove - remove LVM data structure from a physical volume
SYNOPSIS
DESCRIPTION
The command clears the LVM data structure on a disk, so that it is no longer an LVM physical volume. The device may then be used by the
file system or by other volume managers.
The operation is denied if pv_path is assigned to a volume group. The command only clears the LVM data structure on a disk if the disk
does not belong to a volume group. This avoids accidentally removing a valid physical volume under a volume group. If the physical volume
to be removed belongs to a volume group, use the command to first remove the volume group associated with the physical volume.
Arguments
recognizes the following arguments:
pv_path The character (raw) device path name of a physical volume.
EXTERNAL INFLUENCES
Environment Variables
determines the language in which messages are displayed.
If is not specified or is null, it defaults to "C" (see lang(5)).
If any internationalization variable contains an invalid setting, all internationalization variables default to "C" (see environ(5)).
EXAMPLES
Remove LVM data structure on the physical volume
SEE ALSO
lvremove(1M), vgremove(1M), intro(7), lvm(7).
pvremove(1M)