Monitoring Top Talkers PF OpenBSD Post: 302962235

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

please help with openbsd 2.9

Please help. I have downloaded the openbsd 2.9 snapshot from ftp.openbsd.org. the following files were downloaded from the snapshot dir. ( the whole dir. was downloaded ) base29,bsd,bsd.rd,cdrom29.fs,cksum,comp29,etc29,all three floppy images,game29,index,install.ata,install.chs...

2. UNIX for Dummies Questions & Answers

How Can I Have Top Display The Top 20 Processes??

how can i do that in a script withough havin the script halt at the section where the top command is located. am writign a script that will send me the out put of unx commands if the load average of a machine goes beyond the recommended number. top -n 20 i want to save this output to a file...

3. Filesystems, Disks and Memory

Maxtor vs. OpenBSD

Can't setup OpenBSD 3.4 with Maxtor Diamond Plus 9 80Gb ATA/133 HDD... Install process stops at hardware initialize, before installing... :confused: Any Comments... Thanks

4. BSD

OpenBSD and wireless

I've just installed OpenBSD on my laptop (IBM Thinkpad T42) and since this is my first time with wireless networking in OpenBSD I'm a bit lost. What I would like to do is connect to a wireless network using WEP or WPA. Where do I place the key and essid?

5. BSD

Trying to get into OpenBSD

I am an eight year Linux user and after getting into an argument with someone about OpenBSD overiding my theory that OS security is 50% OS and 50% admin skill, I decided to try OpenBSD for myself. I've tried BSDs before and haven't been able to get into them for day to dy use, but I am going to...

6. AIX

Top command in AIX 4.2 (no topas, no nmon, no top)?

Is there a 'top' command equivalent in AIX 4.2 ? I already checked and I do not see the following ones anywhere: top nmon topas

7. Solaris

Monitoring the output of 'top' command on hourly basis.

I need to capture the following data on an hourly basis through cronjob scheduling:- 1. load averages 2. Total no. of processes. 3. CPU state 4. Memory 5. Top 3 process details. All the above information is available through the command 'top'. But here we need to automate the same and...

8. AIX

Need a list of top 10 CPU using processes (also top 10 memory hogs, separately)

Okay, I am trying to come up with a multi-platform script to report top ten CPU and memory hog processes, which will be run by our enterprise monitoring application as an auto-action item when the CPU and Memory utilization gets reported as higher than a certain threshold I use top on other...

9. BSD

openbsd-pf

hello , I wondered if anyone could assist me in writing a simple packet filter firewall on my OpenBSD v4.5. All I intend doing is to have two firewalling machine on a separate network : 192.168.1.1 ext_if = xl0 (dhcp) // Internet interface int_if=xl1 // Internatl interface ...

10. BSD

PF OpenBSD Network Monitoring

Hi, Though I have some Linux background I'm new to BSD. Currently I'm administering an OpenBSD 5.3 firewall which based on PF. I want to view my LAN's top talkers to the internet. If it is a graphical method that's better but I like to know whether it is possible through a command like pfctl....

LEARN ABOUT NETBSD

etherip

ETHERIP(4)						   BSD Kernel Interfaces Manual 						ETHERIP(4)

NAME

     etherip -- EtherIP tunneling device

SYNOPSIS

     pseudo-device etherip

DESCRIPTION

     The etherip interface is a tunneling pseudo device for Ethernet frames.  It can tunnel Ethernet traffic over IPv4 and IPv6 using the EtherIP
     protocol specified in RFC 3378.

     The only difference between an etherip interface and a real Ethernet interface is that there is an IP tunnel instead of a wire.  Therefore,
     to use etherip the administrator must first create the interface and then configure protocol and addresses used for the outer header.  This
     can be done by using ifconfig(8) create and tunnel subcommands, or SIOCIFCREATE and SIOCSLIFPHYADDR ioctls.

   Packet format
     Ethernet frames are prepended with a EtherIP header as described by RFC 3378.  The resulting EtherIP packets will be encapsulated in an outer
     packet, which may be either an IPv4 or IPv6 packet, with IP protocol number 97.

   Ethernet address
     When a etherip device is created, it is assigned an Ethernet address of the form f2:0b:a5:xx:xx:xx.  This address can later be changed
     through a sysctl node.

     The sysctl node is net.link.etherip.<iface>.  Any string of six colon-separated hexadecimal numbers will be accepted.  Reading that node will
     provide a string representation of the current Ethernet address.

   Security
     The EtherIP header of incoming packets is not checked for validity.  This is because there seems to be some confusion about how such a header
     has to look like.	For outgoing packets, the header is set up the same way as done in OpenBSD, FreeBSD, and Linux to be compatible with those
     systems.

   Converting from previous implementation
     A tunnel configured for the previous (undocumented) implementation will work with just renaming the device from gif to etherip.

SEE ALSO

     bridge(4), gif(4), inet(4), inet6(4), tap(4), ifconfig(8)

HISTORY

     The etherip device first appeared in NetBSD 4.0, it is based on tap(4), gif(4), and the former gif-based EtherIP implementation ported from
     OpenBSD.

BUGS

     Probably many.  There is lots of code duplication between etherip, tap(4), gif(4), and probably other tunnelling drivers which should be
     cleaned up.

BSD
								 November 23, 2006							       BSD

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

please help with openbsd 2.9

Discussion started by: Blunt_Killer

2. UNIX for Dummies Questions & Answers

How Can I Have Top Display The Top 20 Processes??

Discussion started by: TRUEST

3. Filesystems, Disks and Memory

Maxtor vs. OpenBSD

Discussion started by: bsdave

4. BSD

OpenBSD and wireless

Discussion started by: Timmy66