10-03-2015
Is the Basis tape cartridge fit the tape drive that you have?
Assuming (always dangerous) that the tape is the same format as Basis shipped on diskette, the tap is a tar tape.
If you can find a suitable tape drive, you can extract the data from the tape and copy it to any suitable medium. There is only 5 x 1.44 diskettes in the distribution, so the tape probably has less than 10mb on it.
You can experiment with transferring the system to a new hard drive by acquiring a Pentium4 system, either socket 478 or 775 with ide disk or sata in legacy mode, PS2 keyboard and mouse, and cd/dvd. You should be able to find a suitable system for about 100 dollars.
You can install 506 using the cd only.
Then install Basis, I have the instructions if you don't, and restore the data files from your current system.
This User Gave Thanks to jgt For This Post:
9 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Help, if possible.
In SCO Open Server with installation of two-channel RAID controller the following happens: on the channel 0 disk array is seen by an operational system, and on the channel 1 array is not seen (simultaneously). That is the operational system can not simultaneously use more than... (1 Reply)
Discussion started by: pko60
1 Replies
2. Filesystems, Disks and Memory
Hi,
I have a server that I am adding a RAID that we purchased to. The server works fine. It is running Fedora 7 and is a Dell Precision 690.
When the RAID is attached, it boots up and says the following:
Controller Bus #00, Device#1F, Function#02: 00 Ports
No device found
AHCI BIOS not... (0 Replies)
Discussion started by: user23
0 Replies
3. Red Hat
I am planning on building a fedora box with raid controller (database server).
Is anybody done that ? also what kind of software do you need to backup and recover data. (1 Reply)
Discussion started by: amir07
1 Replies
4. UNIX for Dummies Questions & Answers
I need to put together a RAID1 file server for use by Windoze systems. I've built zillions of windows systems from components. I was a HPUX SE for a long time at HP, but have been out of the game for years.
I've got an old workhorse mobo FIC PA-2013 with a 450 MHz K6 III+ I could use, but I'd... (2 Replies)
Discussion started by: pcmacd
2 Replies
5. Hardware
Hi All
I have a Sun T2000 server. Couple of years ago I had configured and mirrored the boot drive with an other drive using hardware RAID 1 using raidctl command.
Following is the hardware RAID output.
root@oracledatabaseserver / $ raidctl
RAID Volume RAID RAID Disk... (0 Replies)
Discussion started by: Tirmazi
0 Replies
6. Hardware
Hi guys.
if we want to use SSD drives on a database server, can we use RAID 0 configuration because of their reliability? (3 Replies)
Discussion started by: majid.merkava
3 Replies
7. Linux
I just built a home computer with 3TB hard drives I wanted to set up in a RAID 5 and load Ubuntu server onto it.
The first thing I did was set up the drives in a RAID 5 using just the motherboard chipset software to do it, so a 'hardware' RAID basically.
I installed Windows first to see if... (2 Replies)
Discussion started by: lorewap3
2 Replies
8. Filesystems, Disks and Memory
First time poster and a very new Unix user, so I'll just pre-apologize for stupid questions now.
Does anybody know of a good RAID 1 hard drive backup that is Unix friendly? I want to avoid any hardcore programming. Can you recommend both NAS and non-NAS options? I need to do nightly backups... (31 Replies)
Discussion started by: c.wakeman
31 Replies
9. Hardware
We have a 3ware RAID server at work, and as the appointed systems administrator (by virtue of being the one with the most knowledge) I've taken on the job of maintaining it. I've installed smartmontools on it to keep an eye on the drives and run scans every day, and looking at the data from the... (0 Replies)
Discussion started by: Krendoshazin
0 Replies
tms(4) Kernel Interfaces Manual tms(4)
Name
tms - TMSCP magnetic tape interface
Syntax
For UNIBUS, Q-bus:
controller klesiu0 at uba0
controller uq0 at klesiu0 csr 0174500 vector uqintr
tape tms0 at uq0 drive 0
For MSI Bus:
adapter msi0 at nexus?
controller dssc0 at msi0 msinode 0
tape tms0 at dssc0 drive 3
For VAXBI:
controller klesib0 at vaxbi0 node 0
controller uq0 at klesib0 vector uqintr
tape tms0 at uq0 drive 0
controller aie0 at vaxbi? node?
controller bvpssp0 at aie0 vector bvpsspintr
tape tms0 at bvpssp0 drive 0
For MSI Bus:
adapter msi0 at nexus?
controller dssc0 at msi0 msinode 0
tape tms0 at dssc0 drive 0
For VAX CI/HSC:
adapter ci0 at nexus?
adapter ci0 at vaxbi? node?
controller hsc0 at ci0 cinode 6
tape tms0 at hsc0 drive 3
Description
Prior to Version 2.0, this device was referenced by tmscp(4).
The TMSCP driver provides a standard tape drive interface, as described in This is a driver for any controller that adheres to the Tape
Mass Storage Control Protocol (TMSCP). The TMSCP controllers communicate with the host through a packet-oriented protocol termed the Tape
Mass Storage Control Protocol. This driver also supports n-buffered reads and writes to the raw tape interface (used with streaming tape
drives). See for further details.
Tape Support
TK50, TK70, TF70, TU81, TU81e, TA78, TA79, TA81, RV20, TA90, TA90E, TA91
Diagnostics
All diagnostic messages are sent to the error logger subsystem.
Files
See Also
mtio(4), nbuf(4), MAKEDEV(8), uerf(8), tapex(8)
Guide to the Error Logger
tms(4)