Backup/RAID of HD on Old UNIX Server Post: 302956645

9 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

2-Ch RAID Problem in SCO Open Server

Help, if possible. In SCO Open Server with installation of two-channel RAID controller the following happens: on the channel 0 disk array is seen by an operational system, and on the channel 1 array is not seen (simultaneously). That is the operational system can not simultaneously use more than...

2. Filesystems, Disks and Memory

Adding RAID to server

Hi, I have a server that I am adding a RAID that we purchased to. The server works fine. It is running Fedora 7 and is a Dell Precision 690. When the RAID is attached, it boots up and says the following: Controller Bus #00, Device#1F, Function#02: 00 Ports No device found AHCI BIOS not...

3. Red Hat

linux server with raid controller card

I am planning on building a fedora box with raid controller (database server). Is anybody done that ? also what kind of software do you need to backup and recover data.

4. UNIX for Dummies Questions & Answers

efficient raid file server

I need to put together a RAID1 file server for use by Windoze systems. I've built zillions of windows systems from components. I was a HPUX SE for a long time at HP, but have been out of the game for years. I've got an old workhorse mobo FIC PA-2013 with a 450 MHz K6 III+ I could use, but I'd...

5. Hardware

Hardware RAID on Sun T2000 Server

Hi All I have a Sun T2000 server. Couple of years ago I had configured and mirrored the boot drive with an other drive using hardware RAID 1 using raidctl command. Following is the hardware RAID output. root@oracledatabaseserver / $ raidctl RAID Volume RAID RAID Disk...

6. Hardware

Raid 0 on database server

Hi guys. if we want to use SSD drives on a database server, can we use RAID 0 configuration because of their reliability?

7. Linux

Help Setting up Linux Raid Server

I just built a home computer with 3TB hard drives I wanted to set up in a RAID 5 and load Ubuntu server onto it. The first thing I did was set up the drives in a RAID 5 using just the motherboard chipset software to do it, so a 'hardware' RAID basically. I installed Windows first to see if...

8. Filesystems, Disks and Memory

Help finding a Unix friendly RAID 1 backup

First time poster and a very new Unix user, so I'll just pre-apologize for stupid questions now. Does anybody know of a good RAID 1 hard drive backup that is Unix friendly? I want to avoid any hardcore programming. Can you recommend both NAS and non-NAS options? I need to do nightly backups...

9. Hardware

3ware RAID server

We have a 3ware RAID server at work, and as the appointed systems administrator (by virtue of being the one with the most knowledge) I've taken on the job of maintaining it. I've installed smartmontools on it to keep an eye on the drives and run scans every day, and looking at the data from the...

LEARN ABOUT REDHAT

createhdf

createhdf(1)							     Emulators							      createhdf(1)

NAME

       createhdf - Create a blank IDE hard disk image in .hdf format

SYNOPSIS

       createhdf [ -c ] [ -s ] cylinders heads sectors file
DESCRIPTION

       createhdf creates a blank image of an IDE hard disk in .hdf format for use with Sinclair ZX Spectrum emulators.

OPTIONS

       -c     specifies  that  the  .hdf  image should be created in `compact' mode, where only the low byte of every word is stored in the image.
	      This is useful for saving space if the hard disk image is for use with an interface which accesses only the low byte of every word.

       -s     specifies that the .hdf image should not be created as a sparse file. Normally, createhdf will attempt to create the hard disk image
	      as  a  `sparse  file', where the operating system knows that the file consists mostly of zero bytes and fills those in without using
	      any space in the file. This option disables this. (There's nothing `magic' about this: if data is written to the file, it will  take
	      up space just like any other data; it's only empty space which is synthesised by the operating system).

       -v version
	      specifies  the  version of .hdf image to be created. Valid values are `1.0' for a version 1.0 file and `1.1' for a version 1.1 file.
	      Defaults to creating version 1.1 files.

       cylinders
	      specifies the number of cylinders in the image.

       heads  specifies the number of heads in the image.

       sectors
	      specifies the number of sectors in the image.

       file   specifies the file to which the image should be written.

BUGS

       None known.

SEE ALSO

       fuse(1), fuse-utils(1), libspectrum(3)

       The .hdf format specification, at
       http://www.ramsoft.bbk.org/hdfform.html.

       The comp.sys.sinclair Spectrum FAQ, at
       http://www.worldofspectrum.org/faq/index.html.

AUTHOR

       Philip Kendall (philip-fuse@shadowmagic.org.uk).

Version 1.0.0							16th December, 2010						      createhdf(1)