10-01-2015
Yes, to reinforce what edfair says it is extremely useful in a disaster recovery situation to know how the original disk was laid out. Edfair's post#5 is very important. I second that and reinforce it. Didn't mention it myself because I forgot and I've not used SCO for years.
Thanks also to SCO expert jgt for setting out some very good options.
This User Gave Thanks to hicksd8 For This Post:
9 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Help, if possible.
In SCO Open Server with installation of two-channel RAID controller the following happens: on the channel 0 disk array is seen by an operational system, and on the channel 1 array is not seen (simultaneously). That is the operational system can not simultaneously use more than... (1 Reply)
Discussion started by: pko60
1 Replies
2. Filesystems, Disks and Memory
Hi,
I have a server that I am adding a RAID that we purchased to. The server works fine. It is running Fedora 7 and is a Dell Precision 690.
When the RAID is attached, it boots up and says the following:
Controller Bus #00, Device#1F, Function#02: 00 Ports
No device found
AHCI BIOS not... (0 Replies)
Discussion started by: user23
0 Replies
3. Red Hat
I am planning on building a fedora box with raid controller (database server).
Is anybody done that ? also what kind of software do you need to backup and recover data. (1 Reply)
Discussion started by: amir07
1 Replies
4. UNIX for Dummies Questions & Answers
I need to put together a RAID1 file server for use by Windoze systems. I've built zillions of windows systems from components. I was a HPUX SE for a long time at HP, but have been out of the game for years.
I've got an old workhorse mobo FIC PA-2013 with a 450 MHz K6 III+ I could use, but I'd... (2 Replies)
Discussion started by: pcmacd
2 Replies
5. Hardware
Hi All
I have a Sun T2000 server. Couple of years ago I had configured and mirrored the boot drive with an other drive using hardware RAID 1 using raidctl command.
Following is the hardware RAID output.
root@oracledatabaseserver / $ raidctl
RAID Volume RAID RAID Disk... (0 Replies)
Discussion started by: Tirmazi
0 Replies
6. Hardware
Hi guys.
if we want to use SSD drives on a database server, can we use RAID 0 configuration because of their reliability? (3 Replies)
Discussion started by: majid.merkava
3 Replies
7. Linux
I just built a home computer with 3TB hard drives I wanted to set up in a RAID 5 and load Ubuntu server onto it.
The first thing I did was set up the drives in a RAID 5 using just the motherboard chipset software to do it, so a 'hardware' RAID basically.
I installed Windows first to see if... (2 Replies)
Discussion started by: lorewap3
2 Replies
8. Filesystems, Disks and Memory
First time poster and a very new Unix user, so I'll just pre-apologize for stupid questions now.
Does anybody know of a good RAID 1 hard drive backup that is Unix friendly? I want to avoid any hardcore programming. Can you recommend both NAS and non-NAS options? I need to do nightly backups... (31 Replies)
Discussion started by: c.wakeman
31 Replies
9. Hardware
We have a 3ware RAID server at work, and as the appointed systems administrator (by virtue of being the one with the most knowledge) I've taken on the job of maintaining it. I've installed smartmontools on it to keep an eye on the drives and run scans every day, and looking at the data from the... (0 Replies)
Discussion started by: Krendoshazin
0 Replies
BTSCO(4) BSD Kernel Interfaces Manual BTSCO(4)
NAME
btsco -- Bluetooth SCO Audio
SYNOPSIS
btsco* at bthub?
audio* at audiobus?
DESCRIPTION
The btsco driver provides support for Bluetooth SCO Audio devices through the audio(4) driver.
The btsco driver must be configured at run time with the btdevctl(8) program. The following properties are used by the btsco driver during
autoconfiguration:
local-bdaddr
Local device address.
remote-bdaddr
Remote device address.
service-name
The btsco driver matches the 'HF' and 'HSET' services. For the 'HF' service, the btsco device will, on open(2), listen for incom-
ing connections from the remote device. Otherwise, btsco will attempt to initiate a connection to the remote device.
rfcomm-channel
This integer value is not used directly, but will be stored and passed via the BTSCO_INFO ioctl as below:
SCO connections require a baseband connection between the two devices before they can be created. The btsco driver does not create this, but
can provide information to facilitate an application setting up a control channel prior to use, via the BTSCO_INFO ioctl(2) call on the mixer
device, which returns a btsco_info structure as follows:
#include <dev/bluetooth/btsco.h>
struct btsco_info {
bdaddr_t laddr; /* controller bdaddr */
bdaddr_t raddr; /* headset bdaddr */
uint8_t channel; /* RFCOMM channel */
int vgs; /* mixer index speaker */
int vgm; /* mixer index mic */
};
#define BTSCO_INFO _IOR('b', 16, struct btsco_info)
The btsco driver can be configured to act in Connect or Listen mode. In Connect mode, the btsco driver will initiate a connection to the
remote device on an open(2) call, whereas in Listen mode, open(2) will block until the remote device initiates the connection.
SEE ALSO
bthset(1), ioctl(2), audio(4), bluetooth(4), bthub(4), btdevctl(8)
HISTORY
The btsco driver was written for NetBSD 4.0 by Iain Hibbert under the sponsorship of Itronix, Inc.
BUGS
btsco takes no notice of the HCI Voice Setting in the Bluetooth controller, and this must be 0x0060 (the default) as alternate values are
currently unsupported.
BSD
October 4, 2006 BSD