09-03-2015
Usually I'd just say "ordinary UNIX file access controls" except I don't know what filesystem is on this external drive. What is it?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I am using Redhat 9 Linux, and am trying to get my external usb drive mounted (fat32). If I look at the KDE Control panel, it lists a usb 2.0 storage device under "USB Devices" (also in /proc/bus/usb), and under "SCSI" as scsi1. I looked at /proc/scsi/usb-storage-0, and it lists it there also. What... (6 Replies)
Discussion started by: jeremiebarber
6 Replies
2. Solaris
Is it possible to install Solaris 10 on an external USB drive? I'd like to dual boot Linux and Solaris 10.
Thanks! (2 Replies)
Discussion started by: otterit
2 Replies
3. UNIX for Dummies Questions & Answers
Hi Folks,
I'm a serious UNIX newbie... I'm using a bash shell on Mac OS X.
Basically I took up unix in order to use a specific image processing software package... I've learned enough to write a script to batch process all of my images, but I have so many that I would like to use an... (1 Reply)
Discussion started by: Slanter
1 Replies
4. Solaris
Hello !
What is the comand to mount and usb hard disk ?
I have Solaris 10 installed!
10nx! (1 Reply)
Discussion started by: daniel.balasa
1 Replies
5. SCO
Can anybody help me out to mount USB flash /floppy drive in sco openserver 6.0 . (5 Replies)
Discussion started by: sureshdrajan
5 Replies
6. Solaris
Is there a way to install Solaris 10 x86 with an external DVD drive that connects through the USB port? I would think I would run GRUB off of a floppy disk and somehow use that to make it look to the USB port to boot from but I don't know how to do that. Can anyone help me out? (1 Reply)
Discussion started by: Bradj47
1 Replies
7. Solaris
Hi-
I would like to know if anyone has used any USB External Hard Drive, about 500/750GB or 1TB, with any of the Solaris 10 "SPARC" systems. Not on intel nor amd platform.
I'm looking for the compatible drive and found a few listed on Sun solaris ready page, but I'd like to have inputs from... (3 Replies)
Discussion started by: agfa_109
3 Replies
8. Ubuntu
Hi
I have to buy my selfe external case for hdd but I don't know whether my ubuntu linux, needs some driver to be able to work with this device or it has inside of itselfe this driver ?
rhx for help. (1 Reply)
Discussion started by: presul
1 Replies
9. Hardware
Hi gurus, during playing movie via VLC or SMPlayer I get several time the error that file cannot be read. File was stored on external USB disk. During this error I get another dialogue message that says the new removable disk was connected..., just as if power goes off and on again or if I power on... (1 Reply)
Discussion started by: wakatana
1 Replies
10. UNIX for Advanced & Expert Users
Hello Experts,
I hope I'm writing to the correct category for my question.
I have a very basic shell script for doing file archiving to the external usb hard drive (WD studio edition II 2TB formatted as FAT32 for compatibility). The shell script only needs to run once per day. It basically... (8 Replies)
Discussion started by: johankor
8 Replies
HD(4) Linux Programmer's Manual HD(4)
NAME
hd - MFM/IDE hard disk devices
DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major
device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave
hdd.
General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the
partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order
the partitions are discovered, and only non-empty, non-extended partitions get a number. However, partition numbers 1-4 are given to the
four partitions described in the MBR (the `primary' partitions), regardless of whether they are unused or extended. Thus, the first logi-
cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions
on an IDE disk.
For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS `primary' partition on the
second one.
They are typically created by:
mknod -m 660 /dev/hda b 3 0
mknod -m 660 /dev/hda1 b 3 1
mknod -m 660 /dev/hda2 b 3 2
...
mknod -m 660 /dev/hda8 b 3 8
mknod -m 660 /dev/hdb b 3 64
mknod -m 660 /dev/hdb1 b 3 65
mknod -m 660 /dev/hdb2 b 3 66
...
mknod -m 660 /dev/hdb8 b 3 72
chown root:disk /dev/hd*
FILES
/dev/hd*
SEE ALSO
mknod(1), chown(1), mount(8), sd(4)
Linux 1992-12-17 HD(4)