06-10-2015
Is the HPUX in question v2 or v3 ?
If the answer is v3, the operation can be online, since on v3, every lun has a WWID.
Just do it port by port, rescan and check paths after each, should not be any issues.
If you want to do it offline, do a vgexport preview (to a file not actual export) of all volume groups on the system using SAN disks (just to be safe do it anyway in each scenario) and deactivate the volume group.
Since the VG info is actually written on disks, even if everything changes (disk names etc.) you will be able to import the volume group using a file you created earlier. There are also other methods (vgscan), but this one is most trivial.
Commands you will require are
scsimgr -> to check lunmap and paths before and after.
ioscan -> to rescan after port change.
This assumes you are using hpux native multipath, not other multipath solutions.
10 More Discussions You Might Find Interesting
1. HP-UX
Hi, I'm going to be involved in a migration of SAN islands to one big SAN. I've not worked with SANs before and I'm not sure how to approach this. I suspect the disk devices on the HP servers are going to change, when the EVA's and servers are plugged into this new Cisco 9509 switch.
Any... (0 Replies)
Discussion started by: Hils
0 Replies
2. Solaris
Using Solaris 10 with Veritas Storage Foundation running. I want to copy all contents from DISKA LUN1 to DISKB LUN2. What would be the command syntax to do this? (0 Replies)
Discussion started by: soupbone38
0 Replies
3. Solaris
I have a general question regarding Zone Migration.
I have an older system that is currently running a zone configured with ProFTPD & SSL.
If I want to migrate or clone that zone to another (much newer) system, will I still have to setup & configure ProFTPD & SSL on the new system? (3 Replies)
Discussion started by: em23
3 Replies
4. Red Hat
Hey everyone.
I am working on designing a logging solution for a deployment we have going out in a few months. Right now we have a single storage head end, connected via fibre to a SAN. Basically the plan is to create a number of smaller LUNs on the SAN, and then use LVM2 to handle concatenating... (5 Replies)
Discussion started by: msarro
5 Replies
5. HP-UX
Hello gurus,
I am a SAN Admin - not very familiar with the HPUX administration - so need help with the steps in regards to the migration I need to do at my client place.
Environment: Migrating from CX4 to VMAX - using OR/Hot Pull.
Here are the steps I have put together - HPUX gurus please... (5 Replies)
Discussion started by: jps460
5 Replies
6. Solaris
I am going to do a SAN Array migration and need the sequence of steps required on the Solaris cluster before moving the old array luns to new array luns.
Here are the steps and I need info on the bold points:( I might even be wrong on the sequence of steps please correct me if I am wrong)
1.... (0 Replies)
Discussion started by: sunshinedeepu
0 Replies
7. AIX
Hi all,
We are migrating our SAN storage from HSV360 to 3PAR. The system runs aix 6.1 version with HACMP.
Please let me know what are requirements from OS side and how are the data copied to the new disks. (10 Replies)
Discussion started by: ElizabethPJ
10 Replies
8. Red Hat
I have an IBM blade running RHEL 5.4 server, connected to two Hitachi SANs using common fibre cards & Brocade switches. It has two volume groups made from old SAN LUNs. The old SAN needs to be retired so we allocated LUNs from the new SAN, discovered the LUNs as multipath disks (4 paths) and grew... (4 Replies)
Discussion started by: rbatte1
4 Replies
9. AIX
I'm New to AIX / VIOS
We're doing a FC switch cutover on an ibm device, connected via SAN.
How do I tell if one path to my remote disk is lost? (aix lvm)
How do I tell when my link is down on my HBA port?
Appreciate your help, very much! (4 Replies)
Discussion started by: BG_JrAdmin
4 Replies
10. Solaris
I am working on VM host and collecting data to identify the type of storage attached to the server which will be migrated to VNX.
it has one ldom created on it
luxadm probe output ---
No Network Array enclosures found in /dev/es
Found Fibre Channel device(s):
Node... (7 Replies)
Discussion started by: kpatel786
7 Replies
lvmpvg(4) Kernel Interfaces Manual lvmpvg(4)
NAME
lvmpvg - LVM physical volume group information file
SYNOPSIS
DESCRIPTION
is an ASCII file that stores the volume-group information for all of the physical volume groups in the system. The information is stored
in a hierarchical format.
First, it starts with a volume group under which multiple physical volume groups can exist. Under each physical volume group, a list of
physical volumes can be specified. There must be at least one physical volume group in each volume group that appears in this file. The
physical-volume-group name must be unique within the corresponding volume group, although it is permissible to use a common physical volume
group name across different volume groups. There can be as many volume groups in this file as there are in the system.
Instead of using the and commands, the administrator can edit this file to create and extend physical volume groups. However, care must be
taken to ensure that all physical volumes to be included in the file have already been defined in their respective volume groups by previ-
ous use of or
The file format has the following structure. and are keywords that introduce the names of the volume group and physical volume group,
respectively.
pv_path
...
pv_path
...
pv_path
...
The variables are defined as follows:
pv_path The block device path name of a physical volume within the volume group.
pvg_name The name of the physical volume group. It must be unique within the volume group.
vg_name The path name of the volume group.
EXAMPLES
The following example shows an file containing two volume groups: the first containing two physical volume groups, each with two physical
volumes defined in it; the second containing three physical volume groups, each with one physical volume defined in it.
SEE ALSO
vgcreate(1M), vgextend(1M), vgreduce(1M), vgremove(1M), intro(7), lvm(7).
lvmpvg(4)