06-09-2015
SAN Migration question
Hi,
I am very new to HP-UX, and we're going to be doing a SAN migration.
We're going to take down the machine, and zone it to the new SAN.
My question is, will the device names change and will that interfere with the LVM?
If the new disks come in with different device names, how would I remediate that issue so the LVM would know what disks to point to?
Thanks!
10 More Discussions You Might Find Interesting
1. HP-UX
Hi, I'm going to be involved in a migration of SAN islands to one big SAN. I've not worked with SANs before and I'm not sure how to approach this. I suspect the disk devices on the HP servers are going to change, when the EVA's and servers are plugged into this new Cisco 9509 switch.
Any... (0 Replies)
Discussion started by: Hils
0 Replies
2. Solaris
Using Solaris 10 with Veritas Storage Foundation running. I want to copy all contents from DISKA LUN1 to DISKB LUN2. What would be the command syntax to do this? (0 Replies)
Discussion started by: soupbone38
0 Replies
3. Solaris
I have a general question regarding Zone Migration.
I have an older system that is currently running a zone configured with ProFTPD & SSL.
If I want to migrate or clone that zone to another (much newer) system, will I still have to setup & configure ProFTPD & SSL on the new system? (3 Replies)
Discussion started by: em23
3 Replies
4. Red Hat
Hey everyone.
I am working on designing a logging solution for a deployment we have going out in a few months. Right now we have a single storage head end, connected via fibre to a SAN. Basically the plan is to create a number of smaller LUNs on the SAN, and then use LVM2 to handle concatenating... (5 Replies)
Discussion started by: msarro
5 Replies
5. HP-UX
Hello gurus,
I am a SAN Admin - not very familiar with the HPUX administration - so need help with the steps in regards to the migration I need to do at my client place.
Environment: Migrating from CX4 to VMAX - using OR/Hot Pull.
Here are the steps I have put together - HPUX gurus please... (5 Replies)
Discussion started by: jps460
5 Replies
6. Solaris
I am going to do a SAN Array migration and need the sequence of steps required on the Solaris cluster before moving the old array luns to new array luns.
Here are the steps and I need info on the bold points:( I might even be wrong on the sequence of steps please correct me if I am wrong)
1.... (0 Replies)
Discussion started by: sunshinedeepu
0 Replies
7. AIX
Hi all,
We are migrating our SAN storage from HSV360 to 3PAR. The system runs aix 6.1 version with HACMP.
Please let me know what are requirements from OS side and how are the data copied to the new disks. (10 Replies)
Discussion started by: ElizabethPJ
10 Replies
8. Red Hat
I have an IBM blade running RHEL 5.4 server, connected to two Hitachi SANs using common fibre cards & Brocade switches. It has two volume groups made from old SAN LUNs. The old SAN needs to be retired so we allocated LUNs from the new SAN, discovered the LUNs as multipath disks (4 paths) and grew... (4 Replies)
Discussion started by: rbatte1
4 Replies
9. AIX
I'm New to AIX / VIOS
We're doing a FC switch cutover on an ibm device, connected via SAN.
How do I tell if one path to my remote disk is lost? (aix lvm)
How do I tell when my link is down on my HBA port?
Appreciate your help, very much! (4 Replies)
Discussion started by: BG_JrAdmin
4 Replies
10. Solaris
I am working on VM host and collecting data to identify the type of storage attached to the server which will be migrated to VNX.
it has one ldom created on it
luxadm probe output ---
No Network Array enclosures found in /dev/es
Found Fibre Channel device(s):
Node... (7 Replies)
Discussion started by: kpatel786
7 Replies
LEARN ABOUT HPUX
bootconf
bootconf(4) Kernel Interfaces Manual bootconf(4)
NAME
bootconf - boot device configuration table
DESCRIPTION
The file contains the address and disk layout type of the system's boot devices or lif volumes. It is used by the and HP-UX kernel control
scripts (fileset to determine how and where to update the initial boot loader. Normally the kernel's script queries the system's hardware
and creates the file. In rare cases when either the system configuration cannot be automatically determined or additional and/or alternate
boot devices should be automatically updated, the administrator must edit the file manually.
There is one line in the file for each boot device. Each line contains the following blank-separated fields in the order shown:
disk type A flag indicating how the file system(s) on the disk are laid out. The flag must be one of the following:
Indicates that the root disk is in LVM or VERITAS Volume Manager
(VxVM) format. If LVM or VxVM mirrors are used, then each of the "mirrors" must have its own line in the file.
Indicates that the root disk is in the
"whole disk" format with no partitions, but boot and swap space are reserved outside the file system.
device file The absolute path of the device special file that accesses the physical device where the boot area is located. For LVM root
disks, the device special file is the physical volume(s) returned by the command. For "whole disks" this is the device file
that references the entire disk.
Blank lines are permitted. Any line beginning with a is considered to be a comment.
DIAGNOSTICS
The Software Distributor log file contains diagnostic messages under the fileset if the file is incorrect. Most of the messages are self-
explanatory; a few warrant additional explanation:
If there are no other messages about
the file is probably empty. Otherwise, the file is not in the proper format, and the other messages will explain what the problem
is.
The specified device file does not point to a disk where there is a
lif which contains the file
Some character other than
or is in the first field of a line.
As of release 10.0, the boot areas in
must all be on the same type of disk layout.
There are characters after the
device file specification.
EXAMPLES
The boot area is on an LVM root disk:
l /dev/disk/disk7_p2
The boot area is on a whole disk layout:
w /dev/disk/disk7
WARNINGS
All of the boot devices in the file must have the same disk layout.
AUTHOR
was developed by the Hewlett-Packard Company.
FILES
SEE ALSO
mediainit(1), hpux(1M), hpux.efi(1M), mkboot(1M), vgdisplay(1M), lif(4), intro(7).
documentation.
bootconf(4)