All,
I am using SOLARIS 7. I have formated my hard drive to consist of only 150MB of swap space. This isn't enough considering I am running Oracle. How do I create additional swap space?
Please list sources or commands.
PS mkswap doesn't work on my machine. ( I have swap and... (5 Replies)
Could someone please explain how you know how much swap space you have on your system. See below:
# swap -s
total: 8225048k bytes allocated + 4863488k reserved = 13088536k used, 4008032k available
# swap -l
swapfile dev swaplo blocks free
/dev/dsk/c3t0d0s1 32,25 16... (2 Replies)
Hi,
i have done a blunder here, i increased the swap space on Xen5.6 server machine using below steps :-
1056 dd if=/dev/zero of=/root/myswapfile bs=1M count=1024
1057 ls -l /root/myswapfile
1058 chmod 600 /root/myswapfile
1059 mkswap /root/myswapfile
1060 swapon /root/myswapfile
... (1 Reply)
Dear All,
I have a swap space of 16G available in Sol 10. I have allocated it as a seperate file system. But when the RAM Is full used , the system gets rebooted and the swap is not being used,.
Any reasons for this.
Rgds
Rj (5 Replies)
CENT OS 5.8 server running with a huge java application which uses up all my ram (4GB) and requires excess of atleast 2GB.But the swap is not getting used up((8GB) of swap space left unused) leading a wierd error and stopping application to stop working.
Any one here dealt with the same kind of... (2 Replies)
I've to install Oracle binaries (I'm oracle DBA) and for that I've extend swap space in my home computer. My situation is like this.
# parted -s /dev/sda print free
Model: ATA VBOX HARDDISK (scsi)
Disk /dev/sda: 38.7GB
Sector size (logical/physical): 512B/512B
Partition Table: msdos
... (1 Reply)
Discussion started by: Mukul Sharma
1 Replies
LEARN ABOUT REDHAT
hd
HD(4) Linux Programmer's Manual HD(4)NAME
hd - MFM/IDE hard disk devices
DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major
device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave
hdd.
General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the
partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order
the partitions are discovered, and only non-empty, non-extended partitions get a number. However, partition numbers 1-4 are given to the
four partitions described in the MBR (the `primary' partitions), regardless of whether they are unused or extended. Thus, the first logi-
cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions
on an IDE disk.
For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS `primary' partition on the
second one.
They are typically created by:
mknod -m 660 /dev/hda b 3 0
mknod -m 660 /dev/hda1 b 3 1
mknod -m 660 /dev/hda2 b 3 2
...
mknod -m 660 /dev/hda8 b 3 8
mknod -m 660 /dev/hdb b 3 64
mknod -m 660 /dev/hdb1 b 3 65
mknod -m 660 /dev/hdb2 b 3 66
...
mknod -m 660 /dev/hdb8 b 3 72
chown root:disk /dev/hd*
FILES
/dev/hd*
SEE ALSO mknod(1), chown(1), mount(8), sd(4)Linux 1992-12-17 HD(4)