Automating partitioning setup of /dev/sda on /dev/sdc
Objective: To recreate the partitioning setup of /dev/sda on /dev/sdc
How would I parse the below information and initialize variables
(an array?) that can be used to build sgdisk commands in a script, regardless of the number of partitions?
Something along the lines of:
for each partition listed in text produced by an sgdisk - i command.
I am thinking that I can save this text to a file in the backup process and then use it in the restoration process...
Thank you vey much in advance for any time and effort expended in answering my
question!
Last edited by RogerBaran; 05-21-2015 at 03:52 PM..
Reason: clarification
Please help urgently.
I need to setup up some sort of service on a solaris server on a port.
I dont need it do anything special, anything that is sent to this port from an external server should be dump to /dev/null or a flat file..
Can you help urgently? (1 Reply)
Hi, Anyone can help
My solaris 8 system has the following
/dev/null , /dev/tty and /dev/console
All permission are lrwxrwxrwx
Can this be change to a non-world write ??
any impact ?? (12 Replies)
Hello,
i am using finch (unix commandline instant messaging client using libgnt) which is running connected to /dev/pts/1
Now I would like to "remote control" the program by sending the key combinations normally typed on the keyboard from a programm in another shell. So I tried:... (0 Replies)
Hello,
Ive got an HP LaserJet 2100 / parallel interface.
I had some troubles getting going due to non-working cups drivers. Updated cups and also used a .ppd.gz file from something HP provided. found the files here...
www.linuxprinting.org/show_printer.cgi?recnum=HP-LaserJet_2100
Anyways.... (1 Reply)
So, we removed a LUN from the SAN and the system is refusing to remove the references to it in the /dev folder. I've done the following:
devfsadm -Cv
powermt -q
luxadm -e offline <drive path>
luxadm probe
All those commands failed to remove the path. The drive stills shows up as <drive... (13 Replies)
Hi,
How can i check that i am using RAW devices for storage in my AIX machine...
Also after adding a LUN from storage to a aix host, when i check /dev in the host, i can see both rhdisk and hdisk with same number
eg:
dcback1(root):/dev>ls -lrt | grep disk12
crw------- 1 root ... (4 Replies)
Hello AIXians,
I can't boot my AIX, it hangs and stops at the code error: 0518
After searching google, I knew the problem is due to problems in File Systems.
So the solution is booting from any bootable media, then run these commands in maintenance mode:
#fsck -y /dev/hd4
#fsck -y... (3 Replies)
Hi,
In our HP-UX B.11.11. I could not find dev/urandom and dev/random
Are all pseudo-devices implemented as device drivers, or in need to run /configure some package to install the package to have dev/urandom.
Please help (4 Replies)
Discussion started by: rashi
4 Replies
LEARN ABOUT SUSE
hd
HD(4) Linux Programmer's Manual HD(4)NAME
hd - MFM/IDE hard disk devices
DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major
device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave
hdd.
General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the
partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order
the partitions are discovered, and only nonempty, nonextended partitions get a number. However, partition numbers 1-4 are given to the
four partitions described in the MBR (the "primary" partitions), regardless of whether they are unused or extended. Thus, the first logi-
cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions
on an IDE disk.
For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS "primary" partition on the
second one.
They are typically created by:
mknod -m 660 /dev/hda b 3 0
mknod -m 660 /dev/hda1 b 3 1
mknod -m 660 /dev/hda2 b 3 2
...
mknod -m 660 /dev/hda8 b 3 8
mknod -m 660 /dev/hdb b 3 64
mknod -m 660 /dev/hdb1 b 3 65
mknod -m 660 /dev/hdb2 b 3 66
...
mknod -m 660 /dev/hdb8 b 3 72
chown root:disk /dev/hd*
FILES
/dev/hd*
SEE ALSO chown(1), mknod(1), sd(4), mount(8)COLOPHON
This page is part of release 3.25 of the Linux man-pages project. A description of the project, and information about reporting bugs, can
be found at http://www.kernel.org/doc/man-pages/.
Linux 1992-12-17 HD(4)