03-04-2015
Googling the NVRAM u2103 error seems to indicate your nvram battery is dead. The portion saying "nvram parameters to default values" backs that up. I'm not sure, but most systems have you start your RAM at slot 0 and increment. It may be that this machine had BIOS settings turning off those first RAM slots, but I'd start by looking for the battery on your motherboard, finding a new one and replacing it, and if you get issues with the RAM, try relocating them to slots 0-2 instead of 5-7.
As for the firmware password, Googling that problem indicates you can create a special boot disk if you have access to ANOTHER Sun Sparc 30 (which I'm guessing you don't) or you can replace the boot prom completely. it's Part #525-1669 and you may be able to find one online somewhere. I have zero experience and would be discouraged if I were in your shoes looking at this problem, sorry. I just did some quick Googling for you and have to deal with a couple older Sun machines at work (and wish I didn't have to... lol)
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello everybody!!
I need your help again.
I am using Sun Ultra sparc 60 machine.Follwing are the types of files getting generated in /var/tmp.
"windu_sm_o aaaa,baaa,caaa,daaa" etc.
I am not able to locate which application is generating these files.
Can I straightway delete these files ? or... (1 Reply)
Discussion started by: vikasdeshmukh
1 Replies
2. UNIX for Advanced & Expert Users
Dear All,
I have trouble, I have SPARC Machine and when start for loading, can not finish !
this is copy off message from my system
Netra t 1120/1125 (UltraSPARC-II 440MHz), No Keyboard
OpenBoot 3.31, 512 MB memory installed, Serial #12116535.
Ethernet address 8:0:20:b8:e2:37, Host ID:... (4 Replies)
Discussion started by: heru_90
4 Replies
3. Solaris
I have an ultra sparc 2 with no video - I connect to it with hyperterm.
Is there a way to get to the OK prompt? I have tried control/break and that does not work.
If not is there a video card I can get to put in this box?
I have Solaris 10 installed on this machine.
Thanks (7 Replies)
Discussion started by: tribbles
7 Replies
4. Solaris
In Sparc Ultra 45 machine, how to enable bge1 port, how to do if bge0 is down then bge1 should automatically up.
Thanks & Regards (2 Replies)
Discussion started by: durgaprasadr13
2 Replies
5. Solaris
Hi Gurus,
Can I use null modem cable in Ultra sparc 10 workstation
Thanks (3 Replies)
Discussion started by: kumarmani
3 Replies
6. Debian
Comments/Problems:
Machine boots from CDROM, starts SILO Version 1.4.13,
display welcome message (welcome to Debian GNU/Linux lenny!
built on 20081218-10:06 ).
boot:
Allocated 8 Megs of memory at 0x40000000 for kernel
Loaded kernel version 2.6.26
Loading initial ramdisk... (3 Replies)
Discussion started by: mtk
3 Replies
7. Solaris
Dear Guru,
My boss has a plan to upgrade cpu of server so he needs to know how much better performance(percentage) is Ultra SPARC IV+ 1.95 GHz than Ultra SPARC IV 1.35 GHz?.
I am looking for documentation to reference but I didn't see anything close to my point. If who know,... (3 Replies)
Discussion started by: unitipon
3 Replies
8. Solaris
Hi all.
I am seeing in one of our less-used servers that it crashed and now won't restart. I get the message 'continue with normal startup or boot into maintenance mode'.
I go into maintenance and run fsck on /usr0 (mentioned in error at restart) it then reboots but goes right back to... (3 Replies)
Discussion started by: jamie_collins
3 Replies
9. Solaris
I'm trying to install a PGX32 video card on my Sparc 10 Ultra running Solaris 10.
I've got the Oracle installation guide for it and I got as far as:
"4. Insert the CD-ROM labeled “GFX OpenWindows for Solaris 2” into the drive."
I don't have a CD-ROM by that name and a web search for that... (21 Replies)
Discussion started by: Michele31416
21 Replies
10. UNIX for Beginners Questions & Answers
-> start /SYS
Are you sure you want to start /SYS (y/n)? y
Starting /SYS
]-> show HOST
/HOST
Targets:
bootmode
diag
domain
Properties:
autorestart = reset
autorunonerror = false
bootfailrecovery = poweroff
... (29 Replies)
Discussion started by: z_haseeb
29 Replies
LEARN ABOUT NETBSD
cmdide
CMDIDE(4) BSD Kernel Interfaces Manual CMDIDE(4)
NAME
cmdide -- CMD Technology and Silicon Image IDE disk controllers driver
SYNOPSIS
cmdide* at pci? dev ? function ? flags 0x0000
options PCIIDE_CMD064x_DISABLE
options PCIIDE_CMD0646U_ENABLEUDMA
DESCRIPTION
The cmdide driver supports the CMD Technology PCI0640, PCI0643, PCI0646, PCI0648, PCI0649, and Silicon Image 0680 IDE controllers, and pro-
vides the interface with the hardware for the ata(4) driver.
The 0x0002 flag forces the cmdide driver to disable DMA on chipsets for which DMA would normally be enabled. This can be used as a debugging
aid, or to work around problems where the IDE controller is wired up to the system incorrectly.
SEE ALSO
ata(4), atapi(4), intro(4), pci(4), pciide(4), wd(4), wdc(4)
BUGS
There's no way to reliably know if a PCI064x controller is enabled or not. If the driver finds a PCI064x, it will assume it is enabled
unless the PCIIDE_CMD064x_DISABLE option is specified in the kernel config file. This will be a problem only if the controller has been dis-
abled in the BIOS and another controller has been installed and uses the ISA legacy I/O ports and interrupts.
The PCI0646U controller is known to be buggy with Ultra-DMA transfers, so Ultra-DMA is disabled by default for this controller. To enable
Ultra-DMA, use the PCIIDE_CMD0646U_ENABLEUDMA option. Ultra-DMA can eventually be disabled on a per-drive basis with config flags, see
wd(4).
The timings used for the PIO and DMA modes for controllers listed above are for a PCI bus running at 30 or 33 MHz. This driver may not work
properly on overclocked systems.
BSD
December 13, 2003 BSD