01-06-2015
turns out it was a bad tape drive
8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I'm trying to install a tape drive on a compaq SCO OS 505. well I have gone through the mkdev tape comands and what have you yet no luck. when I reboot and do a simple tape rewind it gives me an error no such device etc.etc. IS there a diference in the xct0 and rct0 a the default?
help.. (2 Replies)
Discussion started by: kikkin
2 Replies
2. Linux
Hello. I have Redhat 8.0 on a laptop. Working good.
I wanted to install the tape drive that is physically attached to it. The tape drive worked fine under Windows98SE. It's one of those parallel QIC-80 drives and I confirmed that it is supported by FTape. It appears that FTape might already... (0 Replies)
Discussion started by: RuralTurtle
0 Replies
3. UNIX for Dummies Questions & Answers
Hi,
I need to restore my tape backup, when I type "tape status" it gives;
status : ready beginning-of-tape write-protected
soft errors : 0
hard errors : 0
underruns : 3
but... (4 Replies)
Discussion started by: alisevA3
4 Replies
4. AIX
I have tape drive in one Lpar. when i saw that time tape is in defined state. After that i deleted the tape drive using the rmdev -R command. Then fired the cfgmgr -v command. But I am not getting the tape drive. Now the drive is even not in defined state also. It is not shown the tape drive. How... (1 Reply)
Discussion started by: pernasivam
1 Replies
5. SCO
Dear All,
I have a tape drive which has worked for offer 3yrs properly on SCO Openserver Release = 3.2v5.0.5. I tried to clean it all invain. I did a fresh installation of unix of the same OS and did the configuration still didn't bear fruits. The tape is a scsi and the configuration is as... (4 Replies)
Discussion started by: njoroge
4 Replies
6. Solaris
Hey folks,
Linux admin here, forced to use Opensolaris to try to use ufsdump/ufsrestore to get some data of some old tapes.
I've got Opensolaris 2009.06 on x86 and a Sony SDX-700V.
As a "control" experiment, I booted the system with a Linux live CD and the tape drive worked perfectly.
... (2 Replies)
Discussion started by: eddy_sysad
2 Replies
7. SCO
I've recently been tasked with "refurbishing" an HP Proliant ML370 running SCO 5.0...something. This is primarily used for legacy support and is kept on a shelf for safe keeping. The scope of work includes hardware diagnostics and blowing the dust out.
I have run HP diagnostics on the array,... (1 Reply)
Discussion started by: v1corp
1 Replies
8. UNIX for Dummies Questions & Answers
Hi,
Using Redhat 5.7. I have Quantum tape drive connected to the server. I am trying to install the Netbackup software. Just wondering how can I see the Quantum is connected to the server. is any command I run to see the tape drive is connected?
I used to work on Solaris, I used to do... (1 Reply)
Discussion started by: samnyc
1 Replies
mt(1) General Commands Manual mt(1)
NAME
mt - magnetic tape manipulating program
SYNOPSIS
tapename] command [count]
Obsolescent
tapename] command [count]
DESCRIPTION
is used to give commands to the tape drive. If tapename is not specified, the environment variable is used; if is not defined, the default
drive is used.
winds the tape in the requested direction (forward or backward), stopping after the specified count EOF marks or records are passed. If
count is not specified, one is assumed. Each EOF mark counts as one record. When winding backwards, the tape always stops at the BOT
marker, regardless of the number remaining in count.
accepts the following commands:
Write count EOF marks.
Forward space
count files.
Forward space
count records.
Backward space
count files.
Backward space
count records.
Rewind tape.
Rewind tape and go offline.
Seek to end of data (DDS and QIC drives only).
Write count setmarks (DDS drives only).
Forward space
count setmarks (DDS drives only).
Backward space
count setmarks (DDS drives only).
Print status information about the tape drive.
Reserve tape drive for sole use by the host issuing the
command (stape or estape driver only).
Release tape drive from sole use by the host issuing the
command (stape or estape driver only).
Spacing operations (back or forward space file or record) leave the tape positioned past the object being spaced to in the direction of
motion. That is, backspacing a file leaves the the tape positioned before the file mark, forward spacing a file leaves the tape positioned
after the file mark. This is consistent with all classical usage on tapes.
WARNINGS
Only raw, no-rewind Berkeley-type devices should be specified. This type of device will not reposition the tape upon close. An example of
such a device is or See mt(7) for more details.
It is possible to wind the tape beyond the EOT marker and off the end of the reel.
A reservation may only be cleared with a release by the host that issued the original reserve. In the event that the host that holds the
reservation is no longer available, the command may be used to reclaim the device by issuing a bus device reset. See st(1M) for more
details.
The reserve/release functionality can only be issued to drives using the or driver.
EXAMPLES
Rewind the tape associated with the device file or (if legacy DSF is disabled):
FILES
Raw magnetic tape interface (stape)
Raw magnetic tape interface (estape)
Default tape interface.
If legacy DSF is disabled, the default value is
AUTHOR
was developed by the University of California, Berkeley.
SEE ALSO
dd(1), st(1M), intro(7), mt(7).
mt(1)