Hmmmm, no LBA value on the disk labels, that is unusual.
However, you can see from your prtvtoc's in post#1 that your new disk is smaller than the old one.
Partition 2 (which on Sun describes the whole disk) sector count says:
Some new filesystems will reserve some space (eg, 100MB) on the drives to manage such a situation but if your filesystem has used the full capacity then there's no alternative but to get one with the same, or more, sectors (LBA's).
Please help me!!!. I am new to Unix and I have to replace the tape backup drive. Originally the system had an IBM tape drive (Rhomat) that is damged. I changed it and installed a dat drive HP 5000+. The hardware recognize the drive, the diagnostics if OK. But when I try to install the operating... (3 Replies)
Hi folks,
I have the following configuration file:
tofu:/tmp # cat bitbandConfig.properties
maestroIp=10.10.10.10
maestroPort=2020
adminPlayPath=<Streaming Agent IP>:2021/streamingGateway/GetPlayList
###This part should not be changed###
adminPlayVODProtocol=http
username=iptv... (7 Replies)
My root disk is failed and how to replace the root disk in AIX.
Can u give a detailed explanation in step wise.
Pls give the answer taking different scenarios.
Regards
Praveen (1 Reply)
Any help appreciated
Sco Unix Ver 5.0+
Have 2 90 gig mirrored drives
Can these be replaced with any similar drive?
Can one just be replaced and will the mirror rebuild on it and then allow reboot on it ---then replace 2nd drive?
Thanks
pb (3 Replies)
I am trying to recover data off a drive that failed in my iMac. Apple returned the drive to me and I purchased a hard drive enclosure. I have been doing research on prices for data recovery services, way too expensive. I seen some links using Unix DD commands in the terminal none of which worked.... (6 Replies)
I am new to the AIX operating system and am seeking out some advice. We recently have had a drive go bad on our AIX server that is in a RAID 10 array. We have a replacement on the way. I was wondering what the correct steps are to swap out this drive. Does the server need to be powered off? Or can... (5 Replies)
I have a AIX 7.1 system that has 3 failed disks, 1 in rootvg and 2 in vg_usr1.
Here is the output of lspv.
# lspv
hdisk0 00044d4dfbb11575 vg_usr1 active
hdisk1 0000150179158027 vg_usr1 active
hdisk2 ... (11 Replies)
Discussion started by: c3rb3rus
11 Replies
LEARN ABOUT XFREE86
prtvtoc
prtvtoc(1M) System Administration Commands prtvtoc(1M)NAME
prtvtoc - report information about a disk geometry and partitioning
SYNOPSIS
prtvtoc [-fhs] [-t vfstab] [-m mnttab] device
DESCRIPTION
The prtvtoc command allows the contents of the label to be viewed. The command can be used only by the super-user.
The device name can be the file name of a raw device in the form of /dev/rdsk/c?t?d?s2 or can be the file name of a block device in the
form of /dev/dsk/c?t?d?s2.
OPTIONS
The following options are supported:
-f Report on the disk free space, including the starting block address of the free space, number of blocks, and unused parti-
tions.
-h Omit the headers from the normal output.
-m mnttab Use mnttab as the list of mounted filesystems, in place of /etc/mnttab.
-s Omit all headers but the column header from the normal output.
-t vfstab Use vfstab as the list of filesystem defaults, in place of /etc/vfstab.
EXAMPLES
Example 1: Using the prtvtoc Command
The following example uses the prtvtoc command on a 424-megabyte hard disk:
example# prtvtoc /dev/rdsk/c0t3d0s2
* /dev/rdsk/c0t3d0s2 partition map
*
* Dimension:
* 512 bytes/sector
* 80 sectors/track
* 9 tracks/cylinder
* 720 sectors/cylinder
* 2500 cylinders
* 1151 accessible cylinders
*
* Flags:
* 1: unmountable
* 10: read-only
* * First Sector Last
* Partition Tag Flags Sector Count Sector Mount Directory
0 2 00 0 76320 76319 /
1 3 01 76320 132480 208799
2 5 00 0 828720 828719
5 6 00 208800 131760 340559 /opt
6 4 00 340560 447120 787679 /usr
7 8 00 787680 41040 828719 /export/home
example#
The data in the Tag column above indicates the type of partition, as follows:
Name Number
UNASSIGNED 0x00
BOOT 0x01
ROOT 0x02
SWAP 0x03
USR 0x04
BACKUP 0x05
STAND 0x06
VAR 0x07
HOME 0x08
ALTSCTR 0x09
CACHE 0x0a
RESERVED 0x0b
The data in the Flags column above indicates how the partition is to be mounted, as follows:
Name Number
MOUNTABLE, READ AND WRITE 0x00
NOT MOUNTABLE 0x01
MOUNTABLE, READ ONLY 0x10
Example 2: Using the prtvtoc Command with the -f Option
The following example uses the prtvtoc command with the -f option on a 424-megabyte hard disk:
example# prtvtoc -f /dev/rdsk/c0t3d0s2
FREE_START=0 FREE_SIZE=0 FREE_COUNT=0 FREE_PART=34
Example 3: Using the prtvtoc Command on a Disk Over One Terabyte
The following example uses uses the prtvtoc command on a disk over one terabyte:.
example# prtvtoc /dev/rdsk/c1t1d0s2
* /dev/rdsk/c1t1d0s2 partition map
*
* Dimensions:
* 512 bytes/sector
* 3187630080 sectors
* 3187630013 accessible sectors
*
* Flags:
* 1: unmountable
* 10: read-only
*
* First Sector Last
* Partition Tag Flags Sector Count Sector Mount Directory
0 2 00 34 262144 262177
1 3 01 262178 262144 524321
6 4 00 524322 3187089340 3187613661
8 11 00 3187613662 16384 318763004
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO devinfo(1M), fmthard(1M), format(1M), mount(1M), attributes(5)WARNINGS
The mount command does not check the "not mountable" bit.
SunOS 5.10 25 Jul 2002 prtvtoc(1M)