Sponsored Content
Full Discussion: Error on network card
Operating Systems Linux Ubuntu Error on network card Post 302929571 by fretagi on Tuesday 23rd of December 2014 04:04:21 AM
Old 12-23-2014
Error on network card

Hi

Please can you help me to understand what could be wrong based on what I have captured in the logs:
I have run
Code:
cat /var/log/syslog | grep -i warn

, and I got the following output
Code:
NetworkManager[7016]: <warn> Activation (eth3) failed.
Dec 23 10:58:25 cmoveldb02 NetworkManager[7016]: <warn> (eth3): DHCPv4 request timed out.
Dec 23 10:58:25 cmoveldb02 NetworkManager[7016]: <warn> Activation (eth3) failed.

the system is running
Code:
ubuntu 12.04

I have run
Code:
ifconfig -a

, and got the following:
Code:
 ifconfig -a
eth2      Link encap:Ethernet  HWaddr 00:23:8b:41:b4:9c
          inet addr:192.168.6.24  Bcast:192.168.6.31  Mask:255.255.255.224
          inet6 addr: fe80::223:8bff:fe41:b49c/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:761426 errors:0 dropped:0 overruns:0 frame:0
          TX packets:774305 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:139384970 (139.3 MB)  TX bytes:109771872 (109.7 MB)
          Interrupt:16 Memory:fcde0000-fce00000

eth3      Link encap:Ethernet  HWaddr 00:23:8b:41:b4:9d
          inet6 addr: fe80::223:8bff:fe41:b49d/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:346190 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:77978155 (77.9 MB)
          Interrupt:17 Memory:fcd80000-fcda0000

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:2325747 errors:0 dropped:0 overruns:0 frame:0
          TX packets:2325747 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:348097678 (348.0 MB)  TX bytes:348097678 (348.0 MB)

 

10 More Discussions You Might Find Interesting

1. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies

2. Cybersecurity

network card physical reset error

Hi all I am facing some problem with network card i am using solaris8 and on sunultra10 .As it is my firewal machine i have got on backup harddisk for any emergency. In one hardidsk while installation only hme0 interface was configured and in the backup hard disk qfe0/hme0 both are... (0 Replies)
Discussion started by: Prafulla
0 Replies

3. UNIX for Dummies Questions & Answers

Installing network card

1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface, 2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out. (1 Reply)
Discussion started by: gops
1 Replies

4. IP Networking

Network Card with SGI

The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out > link ok < when i connected > But... (0 Replies)
Discussion started by: DPAI
0 Replies

5. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies

6. UNIX for Advanced & Expert Users

network card problem

hi, everyone: alpha 600 au true64 Unix 4.0f my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages. "tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies

7. Solaris

[need help] error after configure network card at v890 sparc

hi experts, i have some problem with my server v890, i had config the network with ce0,ce1 and eri0 but after reboot the server have this error messages display : WARNING: ce0: fault detected external to device; service degraded WARNING: ce0: xcvr addr:0x01 - link down configuring IPv4... (2 Replies)
Discussion started by: bucci
2 Replies

8. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies

9. Solaris

How to identifying the network card ?

Hi Experts, Can we use some command from unix to find the available network interface? I did tried Its listing following, however how can I decide the which vender card is attached e.g. if its hme , bge or some thing else Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies

10. Red Hat

Regarding Network Interface Card

Dear All , While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card. Pl find the below alert. Network Interface Card performance for NIC:eth1 has exceeded Major threshold. Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
PBFIFO(8)                                                              Linux                                                             PBFIFO(8)

NAME
pfifo - Packet limited First In, First Out queue bfifo - Byte limited First In, First Out queue SYNOPSIS
tc qdisc ... add pfifo [ limit packets ] tc qdisc ... add bfifo [ limit bytes ] DESCRIPTION
The pfifo and bfifo qdiscs are unadorned First In, First Out queues. They are the simplest queues possible and therefore have no overhead. pfifo constrains the queue size as measured in packets. bfifo does so as measured in bytes. Like all non-default qdiscs, they maintain statistics. This might be a reason to prefer pfifo or bfifo over the default. ALGORITHM
A list of packets is maintained, when a packet is enqueued it gets inserted at the tail of a list. When a packet needs to be sent out to the network, it is taken from the head of the list. If the list is too long, no further packets are allowed on. This is called 'tail drop'. PARAMETERS
limit Maximum queue size. Specified in bytes for bfifo, in packets for pfifo. For pfifo, defaults to the interface txqueuelen, as speci- fied with ifconfig(8) or ip(8). The range for this parameter is [0, UINT32_MAX]. For bfifo, it defaults to the txqueuelen multiplied by the interface MTU. The range for this parameter is [0, UINT32_MAX] bytes. Note: The link layer header was considered when counting packets length. OUTPUT
The output of tc -s qdisc ls contains the limit, either in packets or in bytes, and the number of bytes and packets actually sent. An unsent and dropped packet only appears between braces and is not counted as 'Sent'. In this example, the queue length is 100 packets, 45894 bytes were sent over 681 packets. No packets were dropped, and as the pfifo queue does not slow down packets, there were also no overlimits: # tc -s qdisc ls dev eth0 qdisc pfifo 8001: dev eth0 limit 100p Sent 45894 bytes 681 pkts (dropped 0, overlimits 0) If a backlog occurs, this is displayed as well. SEE ALSO
tc(8) AUTHORS
Alexey N. Kuznetsov, <kuznet@ms2.inr.ac.ru> This manpage maintained by bert hubert <ahu@ds9a.nl> iproute2 10 January 2002 PBFIFO(8)
All times are GMT -4. The time now is 11:05 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy