Please can you help me to understand what could be wrong based on what I have captured in the logs:
I have run
, and I got the following output
the system is running
I have run
, and got the following:
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Hi all
I am facing some problem with network card
i am using solaris8 and on sunultra10 .As it is my firewal machine i have got on backup harddisk for any emergency.
In one hardidsk while installation only hme0 interface was configured and in the backup hard disk qfe0/hme0 both are... (0 Replies)
1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface,
2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out. (1 Reply)
The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out >
link ok < when i connected >
But... (0 Replies)
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
hi, everyone:
alpha 600 au true64 Unix 4.0f
my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages.
"tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
hi experts,
i have some problem with my server v890, i had config the network with ce0,ce1 and eri0 but after reboot the server have this error messages display :
WARNING: ce0: fault detected external to device; service degraded
WARNING: ce0: xcvr addr:0x01 - link down
configuring IPv4... (2 Replies)
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Hi Experts,
Can we use some command from unix to find the available network interface? I did tried
Its listing following, however how can I decide the which vender card is attached
e.g. if its hme , bge or some thing else
Thanks (7 Replies)
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
LEARN ABOUT CENTOS
paps
PAPS(1) General Commands Manual PAPS(1)NAME
paps - UTF-8 to PostScript converter using Pango
SYNOPSIS
paps [options] files...
DESCRIPTION
paps reads a UTF-8 encoded file and generates a PostScript language rendering of the file. The rendering is done by creating outline curves
through the pango ft2 backend.
OPTIONS
These programs follow the usual GNU command line syntax, with long options starting with two dashes (`-'). A summary of options is
included below.
--landscape
Landscape output. Default is portrait.
--columns=cl
Number of columns output. Default is 1.
--font=desc
Set the font description. Default is Monospace 12.
--rtl Do rtl layout.
--paper ps
Choose paper size. Known paper sizes are legal, letter, a4. Default is A4.
--bottom-margin=bm
Set bottom margin in postscript points (1/72 inch). Default is 36.
--top-margin=tm
Set top margin. Default is 36.
--left-margin=lm
Set left margin. Default is 36.
--right-margin=rm
Set right margin. Default is 36.
--help Show summary of options.
--header
Draw page header for each page.
--markup
Interpret the text as pango markup.
--encoding=ENCODING
Assume the documentation encoding is ENCODING.
--lpi Set the lines per inch. This determines the line spacing.
--cpi Set the characters per inch. This is an alternative method of specifying the font size.
--stretch-chars
Indicates that characters should be stretched in the y-direction to fill up their vertical space. This is similar to the texttops
behaviour.
AUTHOR
paps was written by Dov Grobgeld <dov.grobgeld@gmail.com>.
This manual page was written by Lior Kaplan <kaplan@debian.org>, for the Debian project (but may be used by others).
April 17, 2006 PAPS(1)