we have got this error from time to time in our old AIX 6.1 (powerHA 6.1 GLVM) clusters. In deed last week we had to upgrade nodes from AIX 6.1TL6 to TL9 because a problem with clstat/cldump. But this is not your problem..
The steps we use here for all powerHA 6.1 clusters, sure are the same on your link above, are:
Really sorry I can not help in this case...
Last edited by igalvarez; 10-29-2014 at 09:21 AM..
Hello,
I was wondering if I have 3 nodes (A, B, C) all configured to startup with HACMP, but I would like to configure HACMP in such a way:
1) Node B should startup first. After the cluster successfully starts up and mounts all the filesystems, then
2) Node A, and Node C should startup !
... (4 Replies)
This post just as a follow-up for thread https://www.unix.com/aix/115548-hacmp-5-4-aix-5300-10-not-working.html: there was a bug in the clcomdES that would cause the Two-Node-Cluster-Configuration-Assistant to fail even with a correct TCP/IP adapter setup. That affected HACMP 5.4.1 in combinatin... (0 Replies)
Hi
What is the procedure to upgrade the MQ from 6 to 7 in aix hacmp cluster. Do i need to bring down the cluster
services running in both the nodes and then give #smitty installp in both the nodes separately. Please assist... (0 Replies)
Hi all,
I was wondering if someone direct me in how to Make system backup for 2 nodes HACMP cluster ( system image ) .
What are the consideration for this task (3 Replies)
Hi,
I have a IBM Power series machine that has 2 VIOs and hosting 20 LPARS.
I have two LPARs on which GPFS is configured (4-5 disks)
Now these two LPARs need to be configured for HACMP (PowerHA) as well.
What is recommended? Is it possible that HACMP can be done on this config or do i... (1 Reply)
Hi
I'm a little rusty with HACMP, but wanted to find out if it is possible to remove a disk heartbeat network from a running HACMP cluster.
Reason is, I need to migrate all the SAN disk, so the current heartbeat disk will be disappearing. Ideally, I'd like to avoid taking the cluster down to... (2 Replies)
As i have updated a lot of HACMP-nodes lately the question arises how to do it with minimal downtime. Of course it is easily possible to have a downtime and do the version update during this. In the best of worlds you always get the downtime you need - unfortunately we have yet to find this best of... (4 Replies)
Hi,
A customer I'm supporting once upon a time broke their 2 cluster node database servers so they could use the 2nd standby node for something else. Now sometime later they want to bring the 2nd node back into the cluster for resilance. Problem is there are now 3 VG's that have been set-up... (1 Reply)
Hi all,
I remember way back in some old environment, having the HA cluster services not being started automatically at startup, ie. no entry in /etc/inittab.
I remember reason was (taken a 2 node active/passive cluster), to avoid having a backup node being booted, so that it will not... (4 Replies)
HACMP two-node cluster with mirrored LVM.
HACMP two-node cluster with two SAN storages mirrored using LVM. Configured 2 disk heartbeat networks - 1 per each SAN storage. While performing redundancy tests. Once one of SAN storage is down - cluster is going to ERROR state. What are the guidelines... (2 Replies)
Discussion started by: OdilPVC
2 Replies
LEARN ABOUT OPENSOLARIS
sleep
sleep(1) User Commands sleep(1)NAME
sleep - suspend execution for an interval
SYNOPSIS
/usr/bin/sleep
/usr/bin/sleep time
ksh93
sleep time
DESCRIPTION
/usr/bin/sleep
sleep suspends execution for at least the integral number of seconds specified by time.
ksh93
sleep suspends execution for at least the time in seconds specified by time or until a SIGALRM signal is received.
OPERANDS
/usr/bin/sleep
The following operands are supported for /usr/bin/sleep:
time time in seconds can be specified as a non-negative decimal integer number.
ksh93
The following operands are supported:
time Specify time in seconds as a floating point number. The actual granularity depends on the underlying system, normally around 1 mil-
lisecond.
EXAMPLES
Example 1 Suspending Command Execution
The following example executes a command after a certain amount of time:
example% (sleep 105; command)&
Example 2 Executing a Command Every So Often
The following example executes a command every so often:
example% while true
do
command
sleep 37
done
ENVIRONMENT VARIABLES
See environ(5) for descriptions of the following environment variables that affect the execution of sleep: LANG, LC_ALL, LC_CTYPE, LC_MES-
SAGES, and NLSPATH.
EXIT STATUS
The following exit values are returned:
0 The execution was successfully suspended for at least time seconds, or a SIGALRM signal was received (see NOTES).
>0 An error has occurred.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
/usr/bin/sleep
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
|Interface Stability |Committed |
+-----------------------------+-----------------------------+
|Standard |See standards(5). |
+-----------------------------+-----------------------------+
ksh93
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
|Interface Stability |Uncommitted |
+-----------------------------+-----------------------------+
SEE ALSO ksh93(1), wait(1), alarm(2), sleep(3C), wait(3UCB), attributes(5), environ(5), standards(5)NOTES
If the sleep utility receives a SIGALRM signal, one of the following actions is taken:
o Terminate normally with a zero exit status.
o Effectively ignore the signal.
The sleep utility takes the standard action for all other signals.
SunOS 5.11 20 Nov 2007 sleep(1)