10-22-2014
Wisecracker -
Thanks.
What works for me is: 9600 7E1
It is connected to a Point Of Sale scale. I wish to weigh an item and then write the weight to a file.
How do I "Turn off all flow control FTTB"
10 More Discussions You Might Find Interesting
1. Linux
I think my serial port(on board) is not working ......
because when I am running same code on two machines its working good....but when my system comes into picture ....it doesnt show any output comming from serial port..........
can anybody tell me how to configure my serial port.........or to... (16 Replies)
Discussion started by: arunchaudhary19
16 Replies
2. Solaris
Hi,
I am working with solaris 9,SUN-Blade-100 and I want to communicate with the Serial port.To check whether the port is working or not.I write code and when I execute the file,then I got the output--
According to this,serial port is not found.can anyone please tell me how to configure the... (1 Reply)
Discussion started by: smartgupta
1 Replies
3. Programming
I have a need to determine when a string has been completely sent via a serial port from a standard 'C' application. The code is as follows:
SerialPort_Send = open (pPortString, O_WRONLY | O_NOCTTY | O_NONBLOCK);
write (SerialPort_Send, pCommandString, strlen (pCommandString));
... (2 Replies)
Discussion started by: ExDes
2 Replies
4. AIX
Hi,
How can i configure my modem in AIX thru serial port (sa0-->tty0)
I have two port serial card configured as sa0
I created tty1 which port is tty0 and which port is tty1 how can i know?? (1 Reply)
Discussion started by: pchangba
1 Replies
5. UNIX for Dummies Questions & Answers
A neighbour's Ubuntu 10.04 machine has five serial ports, one on the motherboard and four on a PCI card. However, only four cards are showing:
# dmesg | grep tty
console enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
... (2 Replies)
Discussion started by: dotancohen
2 Replies
6. Shell Programming and Scripting
Hi,
I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and... (0 Replies)
Discussion started by: charlie.arya
0 Replies
7. Solaris
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies
8. Shell Programming and Scripting
hello all,
please any one can provide me the shell script to write data to /dev/ttyS1
and read responce from /dev/ttyS1 and compare the responce to some string ..
thnxx
---------- Post updated at 03:35 PM ---------- Previous update was at 11:46 AM ----------
any body help me..
how do i... (1 Reply)
Discussion started by: yashwantkumar
1 Replies
9. Web Development
I need to set a serial port to 9600 7E1. How do I accomplish this?
I've tried every combination, with no luck. (6 Replies)
Discussion started by: Meow613
6 Replies
10. Solaris
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
LEARN ABOUT NETBSD
slattach
SLATTACH(8) BSD System Manager's Manual SLATTACH(8)
NAME
slattach -- attach serial lines as network interfaces
SYNOPSIS
slattach [-Hhlmn] [-s baudrate] [-t ldisc] ttyname
DESCRIPTION
slattach is used to assign a tty line to a network interface which uses asynchronous serial lines.
Currently the slattach command is used to attach sl(4) or strip(4) interfaces. These interfaces have to be created using the ifconfig(8)
create subcommand before the slattach command. The network source and destination addresses and other interface parameters are configured
via ifconfig(8).
The following operands are supported by slattach:
-H Turn on DTR/CTS flow control. By default, no flow control is done.
-h Turn on RTS/CTS flow control. By default, no flow control is done.
-l Turn on the CLOCAL flag, making it possible to run SLIP on a cable without modem control signals (e.g. DTR, DSR, DCD).
-m Maintain modem control signals after closing the line. Specifically, this disables HUPCL.
-n Don't detach from invoking tty.
-s baudrate Specifies the speed of the connection. If not specified, the default of 9600 is used.
-t ldisc Specifies the line discipline to use for the tty. Supported line disciplines are ``slip'' (creates a sl(4) instance) and
``strip'' (creates a strip(4) instance). If this option is not specified, the default is ``slip''.
ttyname Specifies the name of the tty device. ttyname should be a string of the form 'ttyXX', or '/dev/ttyXX'.
Only the super-user may attach a network interface.
To detach the interface, use ``ifconfig interface-name down'' after killing off the slattach process. Interface-name is the name that is
shown by netstat(1).
EXAMPLES
slattach ttyh8
slattach -s 4800 /dev/tty01
DIAGNOSTICS
Messages indicating that the specified interface is not configured or created, the requested address is unknown, or that the user is not
privileged but tried to alter an interface's configuration.
SEE ALSO
netstat(1), daemon(3), netintro(4), sl(4), strip(4), ifconfig(8), rc(8), sliplogin(8), slstats(8)
HISTORY
The slattach command appeared in 4.3BSD.
BUGS
There is no way to specify the interface name (sl%d etc.) to be attached by the slattach command. There is no way to see which interface is
assigned to the specified tty by the slattach command, either.
It would be better if the network interfaces were created by the slattach command rather than by using the ifconfig(8) create subcommand
before the slattach command.
BSD
July 8, 2006 BSD