I have a shell script whose output I want to redict to a log file. So, I can simply redirect the output as shown below.
But, this script is not going to be executed manually or through cron job. Instead, it is invoked by Symantec Netbackup program remotely.
So, I don't get a chance to redirect the output to a log file as shown above.
So, I need to have some mechanism within the script itself to redirect the output to a file. Any idea how I can do this ?
Hi,
I am writing a shell script (ksh, solaris 5.8).
Script is X.sh
variables declared:
LOGFILE=X.log
the script is removing a file:
/usr/bin/rm "$DUMP_FILE1".Z >> $LOGFILE
If I kick off the script from the command line as follows:
./X.sh > X.con 2<& 1 (1 Reply)
Hi all,
I wish to have a script running even if my session is disconnected.
I've tried calling another session within it and using sudo to a different user, but it didn't work - as it was expected to do so :rolleyes:
I guess I'll have to work with "nohup" command, right ?
trying with the... (4 Replies)
Hi ALL,
Is there any way, to login into a website using Shell/Perl command/script?
I am struggling on this from quite sometime but with no luck. Can you guys help, please?
My sole purpose is to login a website (Which requires Username and Password) and then extract some information from... (3 Replies)
Dear all,
good day.
i'm asking about how to disable <control>-c or <control>-z in the beginning of a shell script then enable it again before the script exit
Best Regards
---------- Post updated at 04:41 AM ---------- Previous update was at 04:18 AM ----------
Dear All
i found the... (3 Replies)
hi all,
i want to log every thing happen in my server
is any body can provide me with articals, pdf's
is that correct to log every thing in the system
what is the most important thing i should i log it (4 Replies)
Hi All,
I am preparing a script which executes following things:
1) Logs into 8 cluster one by one.
2) After logging into each cluster,it prints the cluster name & then exit from that cluster.
3) Then it logs to next cluster & peform the same task.
Here is what i have written :
for... (8 Replies)
Hi,
my question is probably quite easy. On one linux machine I have messages being constantly being written to /var/log/messages. An ntpd message comes in every few seconds. I can see new ones with tail messages. On the other machine there seems to be no messages arriving in /var/log/messages.... (3 Replies)
How could I enable logging of bind 9 forwarders messages? I have the following but forwarded requests do not show up in the logs even when running named in debug 10 mode:
logging {
channel syslog_errors { // this channel will send errors or
... (0 Replies)
I have a bash shell script, within it i am using the below two commands . its failing right on scl enable command itself.
if i run it by itself without a shell, it works fine.
by default it is using pythin version 2.6 something. i want to use 3.4 version for that reason with in the shell... (3 Replies)
Discussion started by: cplusplus1
3 Replies
LEARN ABOUT FREEBSD
atf-sh
ATF-SH(1) BSD General Commands Manual ATF-SH(1)NAME
atf-sh [-s shell] -- interpreter for shell-based test programs
SYNOPSIS
atf-sh script
DESCRIPTION
atf-sh is an interpreter that runs the test program given in script after loading the atf-sh(3) library.
atf-sh is not a real interpreter though: it is just a wrapper around the system-wide shell defined by ATF_SHELL. atf-sh executes the inter-
preter, loads the atf-sh(3) library and then runs the script. You must consider atf-sh to be a POSIX shell by default and thus should not
use any non-standard extensions.
The following options are available:
-s shell Specifies the shell to use instead of the value provided by ATF_SHELL.
ENVIRONMENT
ATF_LIBEXECDIR Overrides the builtin directory where atf-sh is located. Should not be overridden other than for testing purposes.
ATF_PKGDATADIR Overrides the builtin directory where libatf-sh.subr is located. Should not be overridden other than for testing purposes.
ATF_SHELL Path to the system shell to be used in the generated scripts. Scripts must not rely on this variable being set to select a
specific interpreter.
EXAMPLES
Scripts using atf-sh(3) should start with:
#! /usr/bin/env atf-sh
Alternatively, if you want to explicitly choose a shell interpreter, you cannot rely on env(1) to find atf-sh. Instead, you have to hardcode
the path to atf-sh in the script and then use the -s option afterwards as a single parameter:
#! /path/to/bin/atf-sh -s/bin/bash
ENVIRONMENT
ATF_SHELL Path to the system shell to be used in the generated scripts.
SEE ALSO atf-sh(3)BSD September 27, 2014 BSD