The IRQ of your serial port hasn't been relevant for about 20 years.
Depending on how your serial port is configured, it may expect RTS/CTS or DTR/DSR handshaking before it will communicate(i.e. will consider the connection 'closed' when certain control lines aren't just right). You can configure this with stty. I think this turns it off.
Hi every body, i have the following problem :
I need to read incoming data from a serial port, this port has connected a weigth device to it that send the weigth and i need to read this data to my aplication, i had this problem in Window Enviroment and i resolve with a "C" routine, but in Unix... (1 Reply)
Hai there,
Can any one provide me with a ansi c source code for
opening com1 or com2 and read data. The port is connected to
another serial communication device on rs232 port.
The o/s is Sco Unix 5.0.6
Matter urgent
Viswanath (0 Replies)
dear sir,
pls. can you help me ? , my os is unix sco 5.0.4 and ,server dat derive (1,4gb)
not working, now i want to transfer my server data in other machine (unix/other possible) by serial port/other port comminication.
thanks
pankaj raval (2 Replies)
Hi,
I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and... (0 Replies)
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
hello all,
please any one can provide me the shell script to write data to /dev/ttyS1
and read responce from /dev/ttyS1 and compare the responce to some string ..
thnxx
---------- Post updated at 03:35 PM ---------- Previous update was at 11:46 AM ----------
any body help me..
how do i... (1 Reply)
hi, I've a problem on my C/C++ program with Posix Library.
I have to read data from the serial but I have incorrect data, in fact I get a bunch of zeros:
"2953.3174, 2785.2126, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0 , 0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0 ,... (24 Replies)
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
LEARN ABOUT NETBSD
spif
SPIF(4) BSD Kernel Interfaces Manual SPIF(4)NAME
spif -- SBus (spiffy) Serial/Parallel Interface
SYNOPSIS
spif* at sbus? slot ? offset ? (sun4c/sun4m/sun4u)
stty* at spif? (sun4c/sun4m/sun4u)
sbpp* at spif? (sun4c/sun4m/sun4u)
DESCRIPTION
The spif driver provides support for the Sun Serial/Parallel Interface card (Sun part number 501-1931), which is based on the Cirrus Logic
CD180 octal serial controller and the Cirrus Logic PPC2 parallel port controller.
The device minor numbers for this driver are encoded as follows:
+---+---+---+---+---+---+---+---+
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
+---+---+---+---+---+---+---+---+
| | | | | | | |
| | | | | +---+---+---> port number
| | | | |
| | | | +---------------> unused
| | | |
| | | +-------------------> dial-out (on tty ports)
| | |
| | +-----------------------> unused
| |
+---+---------------------------> card number
Up to four cards are supported in the system.
Each of the serial ports has an 8 byte FIFO for receive and transmit as well as automatic hardware (RTS/CTS) flow control.
FILES
/dev/ttyS[0123][0-7] Serial ports
/dev/bppS[0-3] Parallel ports
DIAGNOSTICS
spif%d: ccr timeout A timeout occurred while writing to one of the CD180 registers.
stty%d-%d: ring overflow Incoming characters were discarded because the application in control of the device did not read the input fast
enough.
SEE ALSO intro(4), sbus(4), tty(4)HISTORY
The spif adapter was first supported in OpenBSD 2.5. The driver was ported to NetBSD 3.0.
AUTHORS
The driver was written by Jason Wright <jason@thought.net>, and is heavily based on the magma(4) driver written by Iain Hibbert.
TODO
The parallel port is not supported yet.
Dial-out (cua) devices are not yet supported.
BSD February 4, 1999 BSD